44
TOMPYEUOQ2A03C AC Drive Q2A Installation and Operation Instructions
Code
Bezeichnung
Ursache
Fehlerbehebung
FU-Fehlfunktion wurde durch elektrische Störungen
verursacht.
•
Überprüfen Sie die Leitungen im Steuer- und Leistungskreis
sowie die Erdungsverdrahtung, und verringern Sie den Einfluss
der elektrischen Störungen.
•
Stellen Sie sicher, dass die elektrischen Störungen nicht durch
ein elektromagnetisches Schütz verursacht wurden, und ver-
wenden Sie gegebenenfalls ein Überspannungsschutzgerät.
Die Lastträgheit ist falsch eingestellt.
•
Überprüfen Sie die Einstellungen der Lastträgheit bei Netzaus-
fallfunktion, Überspannungsunterdrückung oder Kippschutz
im Tieflauf.
•
Passen Sie
L3-25 [Load Inertia Ratio]
an die Kenndaten der
Maschine an.
Die Kurzschlussbremsfunktion, verwendet bei Vek-
torregelung PM ohne Rückführung.
Schließen Sie einen Bremswiderstand am Frequenzumrichter an.
Der Motor pendelt.
•
Passen Sie
n1-02 [HuntPrev Gain Setting]
an.
•
Passen Sie
n2-02 [AFR Time 1]
und
n2-03 [AFR Time 2]
an.
•
Passen Sie
n8-45 [SpdFbck Det.Gain]
und
n8-47 [Pull-In
Comp.Time Constant]
an.
Die Fangfunktion wird beim Anlauf nicht durchge-
führt, wenn Sie einen Asynchronmotor mit EZOLV-
Regelung verwenden.
Wenn
E9-01 = 0 [Motor Type Selection = IM]
, setzen Sie
b3-24 =
2 [SpSrch Method Selection = Current Det2]
.
PF
Phasenausfall Eingang
Bei der FU-Eingangsspannung liegt ein Phasenver-
lust vor.
Beheben Sie die Fehler bei der Verdrahtung der Eingangsspan-
nung des FU-Leistungsteils.
Lose Verdrahtung an den
Eingangsspannungsklemmen.
Ziehen Sie die Klemmenschrauben mit dem korrekten Anzugsmo-
ment fest.
Die FU-Eingangsspannung schwankt zu stark.
•
Überprüfen Sie die Eingangsspannung auf Probleme.
•
Sorgen Sie für eine stabile FU-Eingangsspannung.
Unzureichende Symmetrie der Spannungsphasen.
•
Überprüfen Sie die Eingangsspannung auf Probleme.
•
Sorgen Sie für eine stabile FU-Eingangsspannung.
•
Wenn die Eingangsspannung in Ordnung ist, überprüfen Sie
das Schütz auf der Leistungsteilseite auf Probleme.
Die Leistungsteilkondensatoren sind unbrauchbar
geworden.
•
Überprüfen Sie die Kondensator-Lebenserwartung in der
Anzeige
U4-05 [Capacitor Maintenance]
.
•
Wenn
U4-05
höher als 90% ist, ersetzen Sie den Kondensator.
Weitere Informationen erhalten Sie beim Hersteller oder einem
Fachhändler.
•
Überprüfen Sie die Eingangsspannung auf Probleme.
•
Schalten Sie den Frequenzumrichter ein.
•
Wenn der Alarm weiterhin besteht, ersetzen sie die Schaltpla-
tine oder den Frequenzumrichter. Weitere Informationen erhal-
ten Sie beim Hersteller oder einem Fachhändler.
STo
STO aktiv
Die Eingänge für
„
Sicherer Halt
“
H1-HC und H2-
HC sind offen.
•
Stellen Sie sicher, dass das Signal für
„
Sicherer Halt
“
von einer
externen Quelle an die Klemmen H1-HC und H2-HC gesendet
wird.
•
Wenn die Funktion
„
Sicherer Halt
“
nicht verwendet wird, ver-
binden Sie die Klemmen H1-HC und H2-HC.
Die zwei
„
Sicherer Halt
“
-Kanäle sind intern
beschädigt.
Ersetzen Sie die Platine oder den Frequenzumrichter. Informatio-
nen zum Austauschen der Steuerplatine erhalten Sie beim Herstel-
ler oder einem Fachhändler.
SToF
Fehler STO Eingang
Eine der zwei Klemmen H1-HC oder H2-HC hat
das Eingangssignal
„
Sicherer Halt
“
empfangen.
Das Eingangssignal
„
Sicherer Halt
“
ist falsch
verdrahtet.
•
Stellen Sie sicher, dass das Signal für
„
Sicherer Halt
“
von einer
externen Quelle an die Klemmen H1-HC und H2-HC gesendet
wird.
•
Wenn die Funktion
„
Sicherer Halt
“
nicht verwendet wird, ver-
binden Sie die Klemmen H1-HC und H2-HC.
Einer der
„
Sicherer Halt
“
-Kanäle ist intern
beschädigt.
Ersetzen Sie die Steuerplatine oder den Frequenzumrichter. Infor-
mationen zum Austauschen der Steuerplatine erhalten Sie beim
Hersteller oder einem Fachhändler.
◆
Entsorgung
■
Hinweise zur Entsorgung
Entsorgen Sie den Frequenzumrichter und das Verpackungsmaterial gemäß den geltenden Gesetzen und Bestim-
mungen auf regionaler und örtlicher Ebene.
Summary of Contents for Q2A-A Series
