background image

13

2. Installation and connection

Notes

Do not short the output lines of the UPS each other and the output lines to the ground.

The UPS may fail.

Do not connect the AC Input Plug of the UPS to its Power Supply Output Receptacle.

The UPS may fail.

Do not connect a page printer to the UPS.

The connection capacity may be exceeded repeatedly during operation using commercial power, which
may cause bypass mode.

It may be detected that the connection capacity is exceeded.

Caution 

Prohibition (things that you must not do)

Do not use the product in a closed place or do not cover the product.

Doing so may cause abnormal heating or a fire.

Concerning installation and storage of the products, follow the instructions
listed below.

Do not install the product in a place where humidity is lower than 20% or higher than 90%.

Do not use the product in a place where humidity is lower than 25% or higher than 85%.

Do not install the products at a closed place such as in a cabinet without clearance, at a place
with flammable gas or corrosive gas exist and in the open air.

Doing so may cause a fire.

Do not connect equipment that exceeds the output capacity of the UPS.
You can use a plug strip and so on to connect extra equipment, but, in
this case, do not connect equipment that exceeds the current capacity of
the plug strip.

The UPS may detect overload and stop the output.

The wiring of the plug strip heats up, which may cause a fire.

Do not insert metal objects into the Power Supply Output Receptacle of
the UPS.

Doing so may cause an electric shock.

Do not install the product in other orientations.

Dropping or falling may cause injury.

Do not obstruct the air inlet and outlet in the side and rear of the product.

Inside temperature increases, which may cause a failure of the UPS and the deterioration of
the battery.

Install the product at least 5 cm from the walls.

Summary of Contents for POWLI BU100XS


















































Reviews: