background image

K8DT-VS

8

Checking Operation

Overvoltages
Gradually increase the input from 80% of the set value.
The input will equal the operating value when the input 
exceeds the set value and the alarm indicator starts flashing.
Operation can be checked by the contact outputs that will 
start after the operating time has passed.
Undervoltage
Gradually decrease the input from 120% of the set value and 
check the operation using the same method as for 
overvoltage.

Example: Overvoltage Operating Mode and an Operating Time of 5 s

Note:

K8DT-VS

@

 output relays are normally operative.

How to Measure the Operating Time

Overvoltage
Change the input suddenly from 0% to 120% of the set value 
and measure the time until the Unit operates.
Undervoltage
Change the input suddenly from 120% to 0% of the set value 
and measure the time until the Unit operates.

Questions and Answers

Q

C

u

rrent inp

u

t

Set 

v

al

u

e

Alarm indicator

Flashing

5 s

Lit

Contact o

u

tp

u

t or

transistor o

u

tp

u

t

V

200 

V

AC

A1

Inp

u

t terminals

Po

w

er s

u

pply

A2

±

C

200 

V

Cycle co

u

nter

V

aria

b

le

a

u

totransformer

0 to 300 

V

Connection Diagram

Q

Summary of Contents for K8DT-VS Series















Reviews: