Omron K8AC-H2 Manual Download Page 19

Page: 19 / 22

K8AC-H

Dimensions

(Unit: mm)

Digital Heater Element Burnout Detectors

Recommended Tools

Recommended Flat-blade Screwdriver

Manufacturer: Phoenix Contact
Model number: SZF0.4

2.5

Crimper for Bar Terminals (Crimping Tool)

Manufacturer: Phoenix

Contact

Model number: CRIMPF0X UD6
Recommended power line diameters: AWG10 to AWG24

Recommended Crimp Terminals

Note: Securely tighten the terminal screws to the following torque:

Power supply terminals: 0.5 N·m
I/O terminals:

0.23 N·m

2.1

1.7

4.5

100

K8AC-H2

@@@

-FLK

To remove a wire, insert the recom-
mended flat-blade screwdriver
straight into the hole under the screw-
less clamp terminal of the wire, and
simply release the wire.

100

K8AC-H1

@@@

-FLK

Terminals

Recommended crimp terminals

Recom-

mended

wire gauge

1 and 2

M3 crimp terminals (Width: 5.8 mm max.)

AWG16 to
AWG18

3 to 14

M2 bar terminals: Al 0.34-8TQ (Phoenix Contact)

AWG22

M2 bar terminals: Al 0.5-8WH (Phoenix Contact)

AWG20

M2 bar terminals: Al 0.75-8GY (Phoenix Contact)

AWG18

5.8 mm max.

Summary of Contents for K8AC-H2























Search results

Summary of Contents for K8AC-H2

Reviews:

Related manuals for K8AC-H2

Brands by name

Popular brands

Omron K8AC-H2, Manual

Search results

Summary of Contents for K8AC-H2

Reviews:

Related manuals for K8AC-H2

Brands by name

Popular brands