background image

K2CU

K2CU

2

Specifications

 Ratings

Item

K2CU-F

K2CU-P

Control supply voltage

100, 110, 200, 220 VAC

100/200, 110/220 VAC

Rated frequency

50/60 Hz

Carry current

1.25 times as large as each model’s
maximum operating current

2.5 A for K2CU-P0.5A-A/-B;
5 A

Operating voltage range

85% to 110% of control supply voltage

Voltage fluctuation compensation
range

85% to 110% of control supply voltage

85% to 110% of control supply voltage
(applicable only on models with voltage
fluctuation compensation)

Operating current

4 to 10 A, 8 to 20 A, 16 to 40 A, 32 to 80 A
(continuously variable)

0.25 to 0.5 A, 0.5 to 1 A, 1 to 2 A, 2 to 4 A
(continuously variable)

Releasing current

105% max. of operating current

110% max. of operating current

Operate time

0.5 s max. (when current changes from 150% to 0%)

Gate input voltage range (for
models with gate input terminals)

5 to 30 VDC

---

Control output

2 A at 220 VAC, SPDT (cos

φ

 = 0.4)

Power consumption

Input: 0.5 VA max.
Power supply: 5 VA max.

Input: 1 VA max.
Power supply: 4 VA max.

 Characteristics

Setting accuracy

±

7% max.

Repeat accuracy

±

3% max.

Influence of temperature

±

10% max. (at 20

°

C

±

30

°

C)

Influence of voltage

Models without voltage fluctuation compensation:

±

3% max. of the value measured at the control supply voltage, on condition that the voltage

fluctuation is 85% to 110% of the control supply voltage
Models with voltage fluctuation compensation:

±

5% max. of the logical value, on condition that the voltage fluctuation is 85% to 110% of the

control supply voltage. (see note)

Influence of frequency

±

3% max. (at 

±

5% of rated frequency)

Insulation resistance

10 M

 min. (at 500 VDC) between electric circuits and mounting panel

Dielectric strength

2,000 VAC, 50/60 Hz for 1 min between electric circuits and mounting panel

Overcurrent

20 times of max. set value of operating current for 2 s

Vibration resistance

Destruction: 16.7 Hz, 1-mm double amplitude for 10 min each in X, Y, and Z directions

Shock resistance

Destruction: 100 m/s

2

 (approx. 10G)

Ambient temperature

Operating: –10

°

C to 55

°

C (with no icing)

Ambient humidity

Operating: 45% to 85%

Weight

K2CU-F: approx. 390 g; K2CU-P: approx. 300 g

Note:

The logical value is an operating value within a range of 0.85 to 1.1 with a voltage fluctuation of 85% to 110%, based on the value at the
control supply voltage measured as 1.

Summary of Contents for K2CU -















Reviews: