●
Meanings of Signal Words
●
Alert statements
■
Dimensions
■
Accessories
■
General specifications
■
When changing camera direction
■
Performance specifications
INSTRUCTION SHEET
Item
Picture element
14.4 W maximum. (12 VDC, 1.2 A maximum)
150 m/s
2
, 3 times each in 6 directions
(up/down, left/right, forward/backward)
Operating and storage : 35 to 85 %
(with no condensation)
10 to 150 Hz, half-amplitude : 0.35 mm
(maximum acceleration 50 m/s
2
)
10 times each in X,Y and Z directions for 8 min
Operating : 0 to 50 °C (with no icing or condensation)
Storage : -25 to 65 °C (with no icing or condensation)
No corrosive gases
Cover for camera : Galvanized steel sheet metal
Case for camera : Aluminum alloy
Case for lens : ABS
Cover for lens: Aluminum alloy
Mount base : Aluminum alloy
Approx. 500 g (including base).
AUTOMATIC FOCUS CAMERA FOR MODEL FZ VISUAL INSPECTION SYSTEM
Model
FZ-SZC100
PRECAUTIONS ON SAFETY
2. Handing the Camera
· Tighten all screws securely during installation.
3. Other Precautions
· Do not use unspecified camera cable other than those that specified in
this manual with the FZ controller. Connection with unspecified
camera cable and/or strobe controller may malfunction at the worst
case.
· When the connector on the back of the camera is not in use, be sure to
cover the connector with the attached cap.
· Do not attempt to disassemble, repair, or modify the Camera.
· If you notice any abnormality in the Camera, stop using it immediately, turn
OFF the power supply, and contact your OMRON sales representative.
· When disposing of the Camera, dispose of it as industrial waste.
Observe the following precautions to ensure safe use of the Camera.
1. Installation Site
Do not install the product in locations subjected to the following
conditions:
· Ambient temperature outside the rating
· Rapid temperrature fluctuations (causing condensation)
· Relative humidity outside the range of 35 to 85%
· Presence of corrosive or flammable gases
· Presence of dust, salt, or metallic particles
· Direct vibration or shock
· Reflection of intense light (such as other laser beams or electric
arc-welding machines)
· Direct sunlight or near heaters
· Water, oil, or chemical fumes or spray
· Strong magnetic or electric field
· Near high-voltage equipment or power equipment
PRECAUTIONS FOR SAFE USE
Observe the following precautions to prevent the product from
malfunctioning, becoming inoperable, or the performance and/or the
device from being adversely affected:
1. Cable
· Use a Camera Cable designed specifically for the Controller.
· Be sure to turn off the power before connecting or disconnecting the
cables.
2. Optical axis
· The center of the optical axis may disperse by camera. When
mounting a camera, always check the central position of video images
with a monitor.
· The center of CCD and the optical axis of the lens are aligned to the direction
of the camera at time of shipment. When the camera direction is changed,
the gap of center of optical axis may become large.
3. Maintenance
· Do not use thinners, benzene, acetone, kerosene to clean the Camera.
· Wipe off stubborn stains carefully with a piece of soft cloth that has
been wetted with a trace quantity of alcohol. Scraches on the front
Panel may cause errors.
· If laege dust particles adhere to the front Panel of the Senser Head,
use a blowerbrush (used to clean camera lenses) to blow them off. Do
not blow the dust particles with your mouth.
4. Magnification
· To avoid collisions of inside lens, maximum value for magnification
setting varies in relation to the focusing value. If magnification is not
sufficient, adjust the working distance.
Main unit, instruction sheet (this manual) and hexagonal wrench
Make adjustment after disconnecting cable from the connector.
Loosen 3 screws located on the ring portion in the figure below using
the attached hexagonal wrench. Turn the ring to adjust the direction.
After adjustment, tighten the screws securely.
■
Connection
(1)Using the Camera cable FZ-VS
□
(sold separately),connect the
connector on the back of the camera and the camera connector on
Controller FZseries.
※
The camera cable (FZ-VS,FZ-VSL,FZ-VSB) is polarized, so,
make sure that the end bearing a nameplate is connected to the
Controller FZseries.
PRECAUTIONS FOR CORRECT USE
FZ-SZC100
To ensure safety, do not use this product for direct or indirect
detection of data from human body.
Do not use this product as a sensing device for the protection
of the human body.
WARNING
659 (H) x 494 (V)
1/3-inch interline color CCD
(reading all pixels)
7.4 (µm) x 7.4 (µm)
Non-interlace mode
80.600Hz
39.336KHz
30.682MHz
12 lines to 480 lines
Internal synchronization
Digital, 10 bit
0dB to +13dB
1/10 to 1/50000s
Electrically driven magnification,
focusing and iris
Zoom
Vari-focal
13 to 100 mm, with tol/- 5%
maximum
77.5 mm to 197.5 mm
480 TV minimum
Minimum: F2.8 (W-end) to F4.7
(T-end)Range of W-end : 2.8 to 8.0
Magnification and focusing:
10,000 times minimum
Iris: 20,000 times minimum
“MG-Wave”series by Moritex Co.
product.
0.7A or less
FZ-SZC100
Item
IEC60529 IP20
Maximum 5 m(FZ-VS
□
)
(Unit: mm)
Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury or in
property damage.
CAUTION
Indicates a potentially hazardous situation which, if not
avoided, will result in minor or moderate injury, or may
result in serious injury or death. Additionally there may
be significant property damage.
WARNING
Camera cable
connector
Illumination connection
connector
Automatic focus camera
FZ-SZC100
Nameplate
Camera cable
FZ-VS
□
© OMRON Corporation 2007 All Rights Reserved.
Thank you for selecting OMRON product. This sheet pri-
marily describes precautions required in installing and
operating the product.
Before operating the product, read the sheet thoroughly to
acquire sufficient knowledge of the product. For your con-
venience, keep the sheet at your disposal.
OMRON Corporation
Suitability for Use
EUROPE
OMRON EUROPE B.V. Sensor Business Unit
Carl-Benz Str.4, D-71154 Nufringen Germany
Phone:49-7032-811-0 Fax: 49-7032-811-199
NORTH AMERICA
OMRON ELECTRONICS LLC
One Commerce Drive Schaumburg,IL 60173-5302 U.S.A
Phone:1-847-843-7900 Telephone Consultation
1-800-55-OMRON Fax : 1-847-843-7787
ASIA-PACIFIC
OMRON ASIA PACIFIC PTE LTD
83 Clemenceau Avenue,#11-01 UE Square,Singapore 239920
Phone : 65-6-835-3011 /Fax :65-6-835-2711
n
THE PRODUCTS CONTAINED IN THIS SHEET ARE NOT SAFETY RATED.
THEY ARE NOT DESIGNED OR RATED FOR ENSURING SAFETY OF
PERSONS, AND SHOULD NOT BE RELIED UPON AS A SAFETY
COMPONENT OR PROTECTIVE DEVICE FOR SUCH PURPOSES.
Please refer to separate catalogs for OMRON's safety rated products.
OMRON shall not be responsible for conformity with any standards, codes, or
regulations that apply to the combination of the products in the customer's
application or use of the product.
Take all necessary steps to determine the suitability of the product for the
systems, machines, and equipment with which it will be used.
Know and observe all prohibitions of use applicable to this product.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING
SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE
SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND
INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL
EQUIPMENT OR SYSTEM.
See also Product catalog for Warranty and Limitation of Liability.
Camera
specifications
Lens
Illumination
Effective pixels
Pixel size
Scanning method
Vertical frequency
Horizontal frequency
Pixel frequency
Number of lines to be read
Synchronization
Video output
Gain
Shutter speed
Operating system
Range of view
Working distance
Resolution
F value
Amperage rating
Connected illumination
Motor durability
(One(1) time is equivalent to
one (1) reciprocating motion)
Power consumption
Vibration
resistance
Shock resistance
Ambient
Temperature
Ambient
humidity
Ambient environment
Degree of protection
Material
Cable length
Weight
50
134
40
7
73.5
45.2
59.4
66.5
25
45.2
20±0.1
46.9
10
10.5
72.2
68
93
89.5
M39X0.5
35
2-M4
DEPTH8
1/4-20UNC DEPTH8
30
28
Maximum 5 m(Model M-RCB40
□
L
by Moritex Co.product.)
Cable length
