manualshive.com logo in svg

Omron F3SG-RA, User Manual

Share
Download
Omron F3SG-RA User Manual Download Page 136

112

Ch
apt
e

r

3

DIP Switch

F3SG-R

User’s Manual

Setting with DIP Switch

3-2-1. DIP Switch on Receiver

The following functional settings are available by DIP Switches on the receiver. A receiver has two DIP
Switches, both of which must be configured based on the table below. For functional details, see
respective chapter in the Functional Details column.

If the settings of two DIP Switches are different, when the power is turned on, F3SG-RA transitions to lockout.

: Indicates a switch position.

You can configure the receiver's DIP Switch position 8 whether the setting of the DIP Switch or the
Configuration Tool should be enabled. If you want to use the Configuration Tool to change the setting,
configure the Position 8 setting as Configuration Tool Enabled. This setting ignores the DIP Switch
setting.
Settings changed with the Configuration Tool are stored in the internal memory of the F3SG-RA. When
any change is made to the settings and then the Position 8 is set to OFF, the F3SG-RA operates

Position

Function

Setting

Description

Functional 

Details

DIP-SW1

DIP-SW2

1

Scan Code

Scan Code A (factory default 
setting)

2-4

Scan Code B

2-4

2

External Device 
Monitoring (EDM)

External Device Monitoring (EDM) 
Disabled (factory default setting)

2-11

External Device Monitoring (EDM) 
Enabled

2-11

3, 4

Interlock/Pre-Reset

Auto Reset (factory default setting)

2-9

Manual Reset
(Start/Restart Interlock)

2-9

Pre-Reset

2-10

Auto Reset (same as factory default 
setting)

2-9

5, 6

Fixed Blanking/
Floating Blanking

Blanking Disabled (factory default 
setting)

-

Fixed Blanking Enabled

2-15

Floating Blanking Enabled

2-16

Blanking Disabled
(Same as Blanking Disabled 
(factory default setting))

-

7

PNP/NPN Selection

PNP (factory default setting)

2-5

NPN

2-5

8

DIP Switch/
Configuration Tool 
Selection

DIP Switch Enabled (factory default 
setting)

See below.

Configuration Tool Enabled

See below.

㻝

㻻㻺

㻝

㻻㻺

㻝

㻻㻺

㻝

㻻㻺

㻞

㻻㻺

㻞

㻻㻺

㻞

㻻㻺

㻞

㻻㻺

㻠

㻻㻺

㻟

㻻㻺

㻠

㻻㻺

㻟

㻻㻺

㻟

㻻㻺

㻠

㻻㻺

㻟

㻻㻺

㻠

㻻㻺

㻟

㻻㻺

㻠

㻻㻺

㻟

㻻㻺

㻠

㻻㻺

㻟

㻻㻺

㻠

㻻㻺

㻟

㻻㻺

㻠

㻻㻺

㻡

㻻㻺

㻢

㻻㻺

㻡

㻻㻺

㻢

㻻㻺

㻢

㻻㻺

㻡

㻻㻺

㻢

㻻㻺

㻡

㻻㻺

㻡

㻻㻺

㻢

㻻㻺

㻡

㻻㻺

㻢

㻻㻺

㻡

㻻㻺

㻢

㻻㻺

㻡

㻻㻺

㻢

㻻㻺

㻣

㻻㻺

㻣

㻻㻺

㻣

㻻㻺

㻣

㻻㻺

㻤

㻻㻺

㻤

㻻㻺

㻤

㻻㻺

㻤

㻻㻺

Summary of Contents for F3SG-RA













































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands