8. Replacing the Battery
This thermometer uses a CR2032 lithium button battery.
Use the battery within the recommended period indicated by its manufacturer.
Replace the battery if “
” and “A1” appear when the thermometer is turned on.
1.
Remove the screw with a small cross-slot screwdriver,
then remove the battery cover.
Note
• To prevent any water from entering into the
thermometer, make sure not to lose the screw
when removing them from the battery cover.
2.
Remove the battery with a thin, pointed object.
Note
• Do not use a metal tool as it may damage the
surrounding parts.
• When removing the battery, be careful not to
injure yourself as the battery may pop out.
3.
Insert new battery with the “+” polarity facing up as
shown in the illustration to the right.
4.
Replace the battery cover and secure it with the screw.
Note
• To prevent any water from entering into the thermometer, DO NOT insert any object
between the thermometer and the battery cover. It may cause damage to the
thermometer.
• After replacing the battery, open the app and press the
button on the thermometer
to set the date and time.
• The supplied battery may have a shorter lifespan than a new battery.
• Dispose of the thermometer, battery and component according to local government
regulations.
9. Restoring Your Thermometer to the Default Settings
To delete all the information stored in your thermometer, follow the instructions
below. Make sure that your thermometer is turned off.
1.
While pressing and holding the button, press the [Power] button within
2 seconds. Then, release both of buttons when “CLR” flashes with a beep
sound.
2.
Press and hold the button for more than 2 seconds.
“CLR” stops flashing with a beep sound, then your thermometer is restored to
the default settings.
3.
Press the [Power] button to turn your thermometer off.
Note
• Your thermometer will automatically turn off after 10 seconds.
• Reverting to the default setting of your thermometer does not delete the information in the app.
10. Maintenance
10.1 Storage
Store the thermometer in the storage case.
Do not store the thermometer:
• In locations exposed to extreme temperatures, humidity, close to heating equipment, direct sunlight, dust, or corrosive
vapors such as bleach.
• In locations where this thermometer may be exposed to vibration or shock.
10.2 Cleaning
Clean your thermometer after every use.
• The thermometer is washable. Wash it under slow running cold/lukewarm water for several seconds
(do not use a sponge or sharp object such as a fingernail or toothpick), and wipe it with a soft dry
cloth. Dry it completely.
• Clean the thermometer using a soft cloth and 70 % isopropyl alcohol.
• Observe the following to prevent damage to the thermometer:
- Do not use benzene, thinner, gasoline or other strong solvents to clean the thermometer;
- Do not soak the thermometer in isopropyl alcohol or hot water (water at a temperature of 122 °F (50 °C)
or higher).
11. Error Messages and Troubleshooting
If any of the below problems occur during measurement, check to make sure that no other electrical device is within
12 inches (30 cm) from the device. If the problem persists, please refer to the table of this section.
Display/Problem
Possible Cause
Solution
Either 0, 1, 2, 4 or 5 appears
with “Er”.
The thermometer may have a malfunction. Contact customer service. Refer to section 14.
Battery cover
Battery
Insert a pointed object
Insert the
battery under
this part and
then press the
battery.
(1)
(2)
Beep
Beep
Display/Problem
Possible Cause
Solution
“AH-” appears.
The thermometer is/was stored in a
location where the temperature is/was
104 °F (40 °C) or more.
Place the thermometer in a location where
the temperature is between 50 and 104 °F (10
and 40 °C) for at least 2 minutes. Then, take a
measurement.
“AL-” appears.
The thermometer is/was stored in a
location where the temperature is/was
lower than 50 °F (10 °C).
When the thermometer is
turned on, “L” appears.
The temperature of the sensor tip is lower
than 89.6 °F (32 °C).
This is not a malfunction.
Keep taking a measurement.
When the thermometer is
turned on, “H” appears.
The temperature of the sensor tip is higher
than 107.6 °F (42 °C).
Cool the sensor tip with a damp towel and
then take a measurement.
When the thermometer
is turned on, a random
reading between 89.6 to
107.6 °F appears.
The sensor tip is warm and the display
shows the actual ambient temperature, if
the ambient temperature is higher than
89.6 °F (32 °C).
“Err” and “°F” appear with a
beep sound.
The thermometer fails to analyze and/or
calculate temperature rising because you
move the thermometer or your mouth
during measurement.
Turn the power off and wait at least
30 seconds, then re-insert the thermometer
correctly to take a measurement again.
“---” and “°F” appear with a
beep sound.
The thermometer is not inserted correctly
or comes out of the mouth during
measurement.
The readings are
inconsistent.
• The sensor tip comes out of the
placement point.
• The sensor tip is placed on different
placement points inside the mouth for
each measurement.
• The mouth is open during measurement.
Use the thermometer correctly. Refer to
section 4.
“ ” flashes any time.
Battery is low.
Replacing the battery with new one is
recommended. Refer to section 8.
Nothing appears or “ ” and
“A1” appear on the display
when the [Power] button is
pressed.
Battery polarity is not
properly aligned.
Check the battery installation for proper
placement. Refer to section 8.
Battery is depleted.
Immediately replace the battery with a new
one. Refer to section 8.
“Err” and “ ”appear.
The thermometer cannot connect to a
smart device or transmit thermometer
readings correctly.
Follow the instructions shown in the app. If
the “Err” and “ ” still appear after checking
the app, contact customer service. Refer to
section 14.
“P” flashes.
The thermometer is waiting to pair with
the smart device.
Refer to section 5 for pairing your
thermometer with your smart device or press
the [Power] button to cancel pairing and turn
your thermometer off.
“
” flashes.
The thermometer is ready to transfer
readings to the smart device.
Open the app to transfer your readings.
“
” flashes.
• Internal stored memory is almost full.
• The date and time are not set after
replacing battery.
Pair or transfer your readings to the app so
the readings will not be lost, and the date and
time will be set. Then, this symbol disappears.
“
” appears.
Internal stored memory is completely full.
Transferring the readings are
not successfully completed.
The thermometer is too far from your
smart device.
Bring the thermometer within 16 ft. (5 m) of
your smart device.
Any other communication
issue occurs.
Follow the instructions shown in the smart device, or visit the “Help” section in the app for
further help. If the problem still persists, contact customer service. Refer to section 14.
If any of the problems below occur, the measurement may have been incorrectly taken. Refer to section 4.
• The reading is higher than usual or “H” appears on the display instead of the reading.
• The reading is lower than usual or “L” appears on the display instead of the reading.
12. Specifications
Model
ET6250
MC-6811T2-Z
Sensing unit
Thermistor
Measurement accuracy
±0.2 °F (89.6 to 107.6 °F) (when measured at a standard room temperature of 73.4 °F
(23 °C) in a test tank held at constant temperature)
Temperature display
4 digits (°F) display in 0.1 degree increments
Measuring site and Reference
body site
Oral
Measurement time
8 to 30 seconds
Power supply
3 V DC, CR2032 lithium button battery
Durable period (service life)
5 years (1 time measurement per day)
Battery life
Approx. 1 year (1 measurement, 1 data transfer per day at a room temperature of
73.4 °F (23 °C))
Measurement mode
Adjusted mode (Predictive temperature measurement)
Transmission method
Bluetooth®
Low Energy
Wireless communication
Frequency range: 2.4 GHz (2400 - 2483.5 MHz)
Modulation: GFSK
Effective radiated power: < 20 dBm
IP classification
IP 22
Operation mode
Continuous operation
Applied part
Type BF (sensor tip and probe)
Protection against electric shock Internally powered ME equipment
Measurement range
89.6 to 107.6 °F
Internal memory
Stores up to 30 readings
Operating conditions
+50 to +104 °F (+10 to +40 °C), 30 to 85 % RH (non-condensing), 700 to 1060 hPa
Storage/Transport conditions
(between uses)
-4 to +140 °F (-20 to +60 °C), 10 to 90 % RH (non-condensing)
Weight
Approx. 1 oz (30 g). (with battery installed)
Dimensions
Approx. 1.3" (w) × 4.8" (l) × 0.7" (d) (32.6 × 122 × 16.6 mm)
Package contents
Thermometer, CR2032 lithium button battery (installed), storage case, instruction
manual, app set-up guide
• The specifications may be changed without prior notice.
• The sensor tip of this thermometer contains nickel.
• Operation mode classification complies with IEC 60601-1.
• IP classification is degrees of protection provided by enclosures in accordance with IEC 60529. This device is protected
against solid foreign objects of 0.5 inch (12.5 mm) diameter and greater such as a finger, and against oblique falling water
drops which may cause issues during a normal operation.
About a wireless communication interference
The Bluetooth option in the product is used to connect to dedicated apps on mobile devices to synchronize date/time
data from mobile device to the product, and to synchronize measurement data from the product to mobile device.
Further handling of the data on the mobile device is up to the user's discretion. This product operates in an unlicensed
ISM band at 2.4 GHz where any third party can intercept the radio waves, willfully or accidentally, for any unknown
purpose. In the event this product is used near other wireless devices such as microwave and wireless LAN, which operate
on the same frequency band as this product, there is a possibility that interference may occur. If interference occurs, stop
the operation of the other devices or relocate this product away from other wireless devices before attempting to use it.
13. FCC Statement
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority
to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Note
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC
radio frequency (RF) Exposure Guidelines. This equipment has very low levels of RF energy that are deemed to comply
without testing of specific absorption ratio (SAR).
14. Limited Warranty
Your ET6250, excluding the battery, is warranted to be free from defects in materials and workmanship appearing within
1 year from the date of purchase, when used in accordance with the instructions provided with the thermometer. The
above warranty extends only to the original retail purchaser, and only to products purchased from an Omron authorized
seller who is subject to and follows Omron’s quality control standards, unless otherwise prohibited by law.
We will, at our option, replace without charge any thermometer covered by the above warranty. Replacement is our only
responsibility and your only remedy under the above warranty.
To obtain warranty service contact Customer Service by calling 1-800-634-4350 for the address of the inspection center
and the return shipping and handling fee. Enclose the original printed receipt. Include a letter, with your name, address,
phone number, and description of the specific problem. Pack the product carefully to prevent damage in transit. Because
of possible loss in transit, we recommend insuring the product with return receipt requested.
THE FOREGOING IS THE SOLE WARRANTY PROVIDED BY OMRON IN CONNECTION WITH THIS PRODUCT, AND
OMRON HEREBY DISCLAIMS ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IMPLIED WARRANTIES AND OTHER TERMS THAT
MAY BE IMPOSED BY LAW, IF ANY, ARE LIMITED IN DURATION TO THE PERIOD OF THE ABOVE EXPRESS WARRANTY.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU.
OMRON SHALL NOT BE LIABLE FOR LOSS OF USE OR ANY OTHER SPECIAL, INCIDENTAL, CONSEQUENTIAL OR
INDIRECT COSTS, EXPENSES OR DAMAGES.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
This warranty provides you with specific legal rights, and you may have other rights that vary by jurisdiction. Because of
special local requirements, some of the above limitations and exclusions may not apply to you.
FOR CUSTOMER SERVICE
Visit our web site at:
OmronHealthcare.com
Call toll free:
1-800-634-4350
15. Guidance and Manufacturer’s Declaration
OMRON Wireless Digital Thermometer
Information for Accompanying Documents in the Scope of IEC60601-1-2:2014
Important information regarding Electromagnetic Compatibility (EMC)
ET6250 conforms to IEC60601-1-2:2014 Electromagnetic Compatibility (EMC) standard.
Further documentation in accordance with this EMC standard is available at OmronHealthcare.com/emc. Refer to the
EMC information for ET6250 on the website.
The
Bluetooth®
word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by
OMRON HEALTHCARE Co., Ltd. is under license.
Other trademarks and trade names are those of their respective owners.
OMRON HEALTHCARE Co., Ltd.
53, Kunotsubo, Terado-cho,
Muko, Kyoto, 617-0002 JAPAN
Distributed by:
OMRON HEALTHCARE, INC.
2895 Greenspoint Pkwy.
Hoffman Estates, IL 60169 USA
OmronHealthcare.com
© 2022 OMRON HEALTHCARE, INC.
Made in China
