Modular Temperature Controller
EJ1
3
■
Characteristics
Note: 1.
The indication of K thermocouples in the
−
200 to 1,300°C range, T and N thermocouples at a temperature of
−
100°C or less, and U and
L thermocouples at any temperature is ±2°C ±1 digit maximum. The indication of B thermocouples at a temperature of 400°C or less is
unrestricted. The indication of R and S thermocouples at a temperature of 200°C or less is ±3°C ±1 digit max.
W = (±0.5% of indication value (PV) or ±3°C, whichever is greater) ±1 digit max. PLII = (±0.5% of indication value (PV) or ±2°C, whichever
is greater) ±1 digit max.
2.
“EU” stands for Engineering Unit. The location of the decimal point depends on the type of sensor that is selected.
If the decimal point locations is set to 0 (****), however, it will be treated as if it were set to 1 (***.*).
3.
B, R, S, and W sensors: 0.2°C/
Ω
max. (100
Ω
max.)
Indication accuracy
Thermocouple input/platinum resistance thermometer input:
(±0.5% of indication value (PV) or ±1°C, whichever is greater) ±1 digit max. (See note 1.)
Analog input: ±0.5% FS ±1 digit max.
CT input:
±5% FS ±1 digit max.
Hysteresis
0.1 to 999.9 EU (in units of 0.1 EU) (See note 2.)
Proportional band (P)
0.1 to 999.9 EU (in units of 0.1 EU) (See note 2.)
Integral time (I)
0 to 3,999 s (in units of 1 s)
Derivative time (D)
0.0 to 999.9 s (in units of 0.1 s)
Control period
0.5 s, 1 to 99 s (in units of 1 s)
Manual reset value
0.0% to 100.0% (in units of 0.1%)
Alarm output setting range
−
1,999 to 9,999 (decimal point position depends on input type)
Sampling period
250 ms
Influence of signal source
resistance
Thermocouple: 0.1°C
(0.2°F)/
Ω
max. (100
Ω
max per line) (See note 3.)
Platinum resistance thermometer: 0.4°C (0.8°F)/
Ω
max. (10
Ω
max per line)
Insulation resistance
20 M
Ω
min. (at 500 VDC)
Dielectric strength
600 VAC, 50/60 Hz for 1 min between current-carrying terminals of different polarity
Vibration resistance
10 to 55 Hz, 20 m/s
2
for 2 hours each in X, Y, and Z directions
Shock resistance
150 m/s
2
max., 3 times each in 6 directions
Weight
180 g
Degree of protection
Rear case: IP20, Terminal section: IP00
Memory protection
EEPROM (non-volatile memory) (number of writes: 100,000)
Standards Approved standards
UL61010C-1, CSA C22.2 No.1010-1
Conformed standards
EN61010-1 (IEC61010-1): Pollution level 2, overvoltage category II
EMC Directive
EMI:
EN61326
EMI Radiated:
EN55011 Group1 class A
EMI Conducted:
EN55011 Group1 class A
EMS:
EN61326
ESD Immunity:
EN61000-4-2
Radiated Electromagnetic Field Immunity:
EN61000-4-3
Burst immunity/Noise Immunity:
EN61000-4-4
Conducted Disturbance Immunity:
EN61000-4-6
Surge Immunity:
EN61000-4-5
Commercial Frequency Immunity:
EN61000-4-8
Voltage Dip/Interrupting Immunity:
EN61000-4-11