background image

1

TEMPERATURE CONTROLLER

E5EX–H

DIN-sized (96 x 48-mm) Temperature

Controller Featuring Advanced PID

Control and Heater Burnout Detection

Advanced PID control with two degrees of freedom
improves stability and response speed.

Heater burnout alarm built in.

Select from seven temperature sensors and a total
of 14 temperature ranges (seven Fahrenheit and
seven Celsius).

High accuracy: 0.3% of set value.

Ordering Information

The model numbers for the basic Temperature Controller, its five Control Output Units, and two Current Transformers are given below. Be sure
to specify an Control Output Unit and Current Transformer when ordering.
Example: E5EX–AH, Relay Output Unit E53–R, Current Transformer E54–CT1

Models set to display in degrees Fahrenheit (

°

F) can be ordered by adding “–F” to the end of the model number. Example: E5EX–AH–F

The scale indication switch will then be set to 

°

F prior to shipment from the factory.

 Temperature Controllers

Model

E5EX–AH

 Control Output Units

Output

Relay output

SSR output

Voltage output (for driving SSR)

12 VDC, NPN

24 VDC, NPN

24 VDC, PNP

Model

E53–R

E53–S

E53–Q

E53–Q3

E53–Q4

 Current Transformers

Hole diameter

5.8 mm

12.0 mm

Model

E54–CT1

E54–CT3

 Temperature Ranges

Input (switch

selectable)

Thermocouple

Temperature

resistance

thermometer

K (CA)

Chromel vs.

alumel

J/L (IC) 

Iron vs.

constantan

T/U (CC)

Copper vs.

constantan

E (CRC)

Chromel

vs.

constantan

R (PR)

Platinum vs.

platinum

rhodium 13%

Platinum vs.

platinum

rhodium 10%

PT platinum

resistance

thermometer

(Pt100/JPt100)

Range

°

C

–200 to 1,300

–100 to 850

–200 to 400

0 to 600

0 to 1,700

0 to 1,700

–99.9 to 450.0

°

F

–300 to 2,300

–100 to 1,500

–300 to 700

0 to 1,100

0 to 3,000

0 to 3,000

–99.9 to 800.0

Resolution (

°

C/

°

F)

(main settings and
alarm)

1

0.1

Summary of Contents for E5EX-H

















Reviews: