background image

E3X-N

E3X-N

4

Nomenclature

E3X-NT11 (NPN)
E3X-NT21 (NPN)
E3X-NT41 (PNP)
E3X-NT51 (PNP)

E3X-NM11 (NPN)
E3X-NM41 (PNP)

Operation indicator (orange)

Stability indicator (green)

Teaching indicator (red/green)

Teaching button

Mode selector

Timer switch (see note)

Operation mode selector

Four operation 
indicators (orange)

Four stability 
indicators (green)

Channel selector

Teaching 
indicator (red/green)

Operation mode 
selectors

Teaching button

Mode selector

Note: The E3X-NT11 or E3X-NT41 do

not have a timer function.

Operation

CHOOSING THE RIGHT TEACHING METHOD

Refer to the following table to select the most suitable sensitivity setting method.

Teaching method

Maximum sensitivity setting

No-object teaching

With/Without-object teaching

Typical application

Detection of the existence of
objects that interrupt light
perfectly

Detection of objects with no
background objects

If teaching is impossible by
stopping the movement of
sensing objects

To detect bright or dark objects
by teaching only with background
objects

Detection of a slight difference in
reflection

Color discrimination

Background objects with
unstable reflection

Detection of object surface
irregularities

Elimination of background object influence

Note: 1. None of the four channels has any output when the E3X-NM (four channels) is in teaching mode (i.e., all the four channels will

be in teaching mode).

2. If the set distance is very short (i.e., 0 to 12 mm for the E32-TC200 and 0 to 4 mm for the E32-DC200), no-object teaching is

not possible due to excessive light, in which case, perform with/without-object teaching.

3. In principle, use the E3X-NM (four channels) for the close connection of a maximum of four Fiber Units. When closely connect-

ing two to three Fiber Units to more than one E3X-NT (one channel), perform with/without-object teaching, in which case teach-
ing must be performed on a single E3X-NT at a time. Therefore, turn on only the E3X-NT on which teaching is performed. If all
the E3X-NTs are turned on, interrupt the emitters of the Fiber Units on which teaching is not performed.

Summary of Contents for E3X-N















Reviews: