background image

1

Do not use this product in applications which require an extremely high degree 
of reliability and safety, such as those listed below. 

(This product is designed and manufactured for use for OA equipment such as personal computers.)

 Medical equipment or system that may cause death directly

 Applications that directly affect the safety of people. (For example, the operation and control of cars and 

elevators.)

 Applications in which failure may signi

fi

 cantly damage or impact the society and public. (For example, 

important computer systems or communication equipment.)

 Applications with the same level of importance as those described above.

Do not disassemble, repair, or modify the product.

 Doing so may cause an electric shock or a 

fi

 re.

If liquid leaks from the product, do not touch it.

 Doing so may cause blindness or burns.

 If it touches your eyes or skin, wash it out with lots of clean water and consult your doctor.

: Indicates a prohibited action (something you must not do). For example, 

 indicates that 

disassembly is prohibited.

: Indicates a necessary action (something you must do). For example, 

 indicates that grounding 

is necessary.

This manual contains important information regarding the safe 

use of this product.

Please read these instructions before installation and/or use.

Indicates an imminently hazardous situation which, if not handled 
properly, may result in death or serious injury.

Indicates a potentially hazardous situation which, if not handled 
properly, may result in injury or property damage.

Warning

Caution

Safety precautions

 The safety symbols used in this manual are explained below.

  * Property damage means damage to houses/household effects, livestock, and pets.

Note that some items described as cautions may result in more serious damage under certain condi-
tions.The information described here is very important and must be strictly observed.

Warning

Caution 

(installation)

Warning 

(product use)

 This manual contains important information regarding the safe use of the BUM100R/300R. Please read 

these instructions before installing and/or using the product.

 Please connect and install the battery unit only after having fully understood the relevant procedures for 

the Backup Power Supply, found in the Backup Power Supply Instruction Manual.

Two or more people should work together to carry, unpack and install. 

 Because the unit is heavy, you may injure yourself or drop the unit, or it may fall over. 

The weight of the BUM100R is 26kg, and the weight of the BUM300R is 42kg. 
Carefully consider the weight when unpacking and transporting this product.
For information about repairs, contact us at __________.

 Injury may result if the unit falls or is dropped.

  If you drop the unit, stop using it and have it inspected and repaired. 

Keep plastic bags out of the reach of children.

 Children may suffocate if they put their heads into plastic bags.

Battery Unit BUM100R/BUM300R Instruction Manual

Summary of Contents for BUM100R































Reviews: