manualshive.com logo in svg

OmniSwitch os6900, Network Configuration Manual, Page: 475 / 942

Share
Download
OmniSwitch os6900 Network Configuration Manual Download Page 475

Configuring BFD

Configuring BFD

OmniSwitch AOS Release 7 Network Configuration Guide

June 2013

page 20-11

carried explicitly in the protocol, but rather, it is determined by the receiving system independently based 
on the transmission interval (TX) and Detection Time Multiplier that have been negotiated. 

The Detection Time Multiplier field value is approximately the number of packets that must be missed in 
order to declare a session down. In Asynchronous mode, detection times can be different in each direc-
tion. The local system detection time in this mode equals the value of Detection Time Multiplier received 
from the remote system multiplied by the negotiated transmission interval (TX). Because the time values 
for BFD control packet transmissions and session detection are being constantly negotiated by the partici-
pating BFD peers, they can be changed at any time. They are also independent in each direction for each 
session. 

To change the rate at which BFD control packets are received, you can change the Required Min RX 
Interval at any time to any value. This new value is sent in the next outgoing packet so that the remote 
system can accommodate the changes made. Similarly, to change the rate at which BFD control packets 
are transmitted, you can change the Desired Min TX Interval at any time to any value.

With some exceptions, a system cannot transmit control packets with an interval shorter than the larger 
value of the TX interval and RX interval fields. This means that the system with the slower rate deter-
mines the BFD control packet transmission speed.

Configuring BFD

Configuring BFD for your network requires the following approach: 

1

Optional

: Configure a BFD session and related session parameter values. Once configured, enable all 

participating BFD sessions 

before

 configuring BFD interoperability with the supported Layer 3 protocols. 

See 

“Configuring BFD Session Parameters” on page 20-11 

for more information.

2

Configure BFD support for the Layer 3 protocols for which BFD establishes sessions. This implemen-

tation of BFD supports the IPv4 versions of BGP, OSPF, VRRP remote tracking, and static routes. See 

“Configuring BFD Support for Layer 3 Protocols” on page 20-15 

for more information.

At the end of the chapter is a simple BFD network diagram with instructions on how it can be created on a 
router-by-router basis. See 

“BFD Application Example” on page 20-23

 for more information.

Configuring BFD Session Parameters

When a BFD session is created, default values are automatically set for these parameters. However, it is 
possible to change these parameter values globally or for a specific BFD session. The following BFD 
session parameter values are used to create, monitor, and negotiate BFD sessions between peers. 

•

BFD session status (see 

“Configuring a BFD Session” on page 20-12

).

•

Transmit time interval (see 

“Configuring the BFD Transmit Time interval” on page 20-12

).

•

Receive time interval (see 

“Configuring the BFD Receive Time Interval” on page 20-12

).

•

Multiplier (see 

“Configuring the BFD Multiplier” on page 20-13

).

•

Echo interval (see 

“Configuring the BFD Echo interval” on page 20-13

).

Summary of Contents for os6900















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments