background image

 

 

DMAN-xxxx-xx

 

www.omnexcontrols.com

 

call toll free: 1-800-663-8806

 

Follow these steps to download the transmitter’s unique ID Code into the receiver.  This will allow the receiver to establish 
a Radio link with a specific transmitter.  Refer to Troubleshooting Chart #4 for Tips and Considerations 
 

NOTE:  It is necessary to download the ID code when replacing either the transmitter or the receiver. 
 
NOTE: If the transmitter is connected to the receiver with a Tether Cable, completing only steps 4 and 6 is necessary (it is not 
necessary to open the R160 case and press the Setup button). 

Follow these steps to ensure that there is a Radio Link between the transmitter and receiver 

Refer to the Light Legend below for diagram details 

1. Press [E-Stop] 

ESTOP 

FAULT  LINK 

STATUS 

2. Power the R160 

ESTOP 

FAULT  LINK 

STATUS 

3. Power the T300 

If the (Active) light on the transmit-
ter is flashing and the (Link) light 
on the receiver is flashing GREEN, 
a link between the two exists. 

The (E Stop) light and the (Link) 
light will come on RED (provided the 
transmitter is off), and the (Status) 
light will come on GREEN.

 

NOTE: 

The transmitter will shut itself off (and the receiver will then shut off all outputs) after 4 hours of inactivity as a battery saving feature.  To restart 

the timer before the transmitter shuts off automatically, momentarily operate any toggle switch or paddle.

 

The ORIGA System is now ready for use. 

If the receiver's (Link) light does not become GREEN follow the steps under Download ID Code first then Refer 
to Troubleshooting guide for more information. 

 

The cap is held on by two plastic tabs at 
opposing sides, which can be unlatched as 
shown using a screwdriver.  Once the cap 
is free, the R160 can slide open. 

Use a small slotted screwdriver to press the 
Side Tabs inward. 

ESTOP 

FAULT  LINK  STATUS 

1. Opening the R160 Case 

 

A. Press [E-Stop] 

B. Twist CW & release [E-Stop] 

2. Prepare T300 

A. 

B. 

 Test the Transmitter / Receiver Link 

Download ID Code 

(Use in case of Link Test failure) 

Light Legend  

Solid 

Slow  
Flash 

Fast  
Flash 

Red  
Light 

Green  
Light 

Alternating Red 
& Green Light 

Yellow 
Light 

NOTE: When replacing the receiver cover, ensure the cover snaps completely into place to create a weather proof seal around the 
base of the receiver. 

 

StockCheck.com

Downloaded from StockCheck.com

Summary of Contents for GENERIC D160

















Reviews: