background image

6

7

WARNINGS AND CAUTIONS

WARNINGS AND CAUTIONS

NEVER DISASSEMBLE BOWL SET DURING OPERATION OR 

INSERT FINGERS, FOREIGN OBJECTS SUCH AS FORKS, SPOONS ETC. 

INTO FEEDING TUBE OR JUICE OUTLET.

 

It may cause an injury, an accident or a failure.

THIS APPLIANCE IS NOT INTENDED FOR USE BY PERSONS (INCLUDING 

CHILDREN) WITH REDUCED PHYSICAL, SENSORY OR MENTAL CAPABILITIES, 

OR LACK OF EXPERIENCE AND KNOWLEDGE, UNLESS THEY HAVE BEEN GIVEN 

SUPERVISION OR INSTRUCTION CONCERNING USE OF THE APPLIANCE BY 

A PERSON RESPONSIBLE FOR THEIR SAFETY.

Children should be supervised to ensure that they do not play with the appliance.

CAUTION

Hazards or unsafe practices which could result in minor personal injury or 
appliance damage.

DO NOT OPERATE WITHOUT LOCKING THE HOPPER PROPERLY.

It may cause an injury or a failure.

WHEN DETECTING A GAS LEAK, DO NOT INSERT THE POWER CORD INTO ITS 

SLOT. OPEN THE WINDOW TO VENTILATE FULLY AND IMMEDIATELY.

It may cause an injury or a failure.

NEVER PUT A FINGER, A FORK OR A SPOON ETC. INTO JUICE OUTLET.

It may cause an injury or a failure.

IF SCREW ROTATION IS STOPPED IN NORMAL OPERATION, PRESS [REVERSE/REV] 

BUTTON AND HOLD FOR 2~3 SECONDS AND THEN AFTER REVERSE OPERATION 

IS COMPLETELY STOPPED, PRESS [ON] BUTTON AGAIN.

If such a stop event continues duringthe operation, the parts may be damaged and 

performance may be deteriorated due to overheating in a motor. When the problem 

continues, immediatly stop the appliance and contact the local Customer Care Center.

DURING THE OPERATION, DO NOT ATTEMPT TO MOVE THE BASE, 

DISASSEMBLE THE BOWL SET OR PARTS AND TRY TO LOCK THEM.

It may cause an injury or a failure. 

Any act of event needed, switch off first and unplug the power cord.

WHEN USING THE APPLIANCE, BE CAREFUL FOR A NECKTIE, LONG NECKLACE, 

SCARF ETC. NOT TO BE ENTANGLED INTO FEEDING TUBE.

It may cause an injury, a failure or a breakage.

PLACE THE APPLIANCE ON A FLAT AND STABLE SURFACE.

It may cause an injury or a failure.

DO NOT OPERATE THE APPLIANCE FOR MORE THAN 30 MINUTES AT A TIME.

It may cause a motor failure due to overheating.

Cool it down sufficiently for 5 minutes and operate it again.

WHEN PLACING INGREDIENTS INTO THE FEEDING TUBE, ONLY USE THE 

PUSHER PROVIDED.

It may cause an injury or a failure.

DO NOT ALLOW A SEVERE SHOCK TO THE APPLIANCE OR DROP IT.

It may cause an electric shock, a fire or damage.

IF THE APPLIANCE GIVES OFF AN UNPLEASANT SMELL OR EXCESSIVE 

HEATING, SMOKE, STOP USING IMMEDIATELY AND CONTACT THE LOCAL 

CUSTOMER CARE CENTER.

When using a new appliance, it gives off a smell and the smell disapears naturally over time.

ALWAYS UNPLUG THE APPLIANCE AFTER USE. 

WHEN UNPLUGGING THE POWER CORD, MAKE SURE TO HOLD THE POWER CORD.

If holding the wire to unplug, it may cause an electric shock or a fire.

DO NOT WASH AT HIGH TEMPERATURES OF 800C (1760F) OR MORE.

DO NOT PUT THE APPLIANCE IN A DISHWASHER, A DRYER OR A MICROWAVE ETC.

It may cause a failure or parts deformation.

THE APPLIANCE WEIGHS ABOUT 6KG (13.2LB).

WHEN MOVING THE APPLIANCE, ENSURE TO MOVE IT HOLDING GRIPS TIGHTLY

AT THE BASE BOTTOM WITH BOTH HANDS.

If attempting to hold bowl or the edge of the base, the base falls causing an injury 

or a failure.

Summary of Contents for VRT400 SERIES















Reviews: