background image

Where to put your Omega Turbo Charger

Place your Turbo Charger on a smooth flat surface. Do not operate / store in dusty humid conditions
or below 35 F.
Allow 2” space behind compressor for air exiting.
For long term storage, keep indoors and away from freezing temps. In sub-zero temps, drain water
tank and fill with pure antifreeze, run for 1 min. Use supplied cover.

Fill times

Typically, for a rifle 2-3 min
A 12cf tanks takes 20-25 min from 0-4500 psi
A 75cf tank take 1.25 -1.5 hrs from 0-4500 psi

Maintenance

After every 6 hrs of compressor operation or when the red indicating light comes on, turn green
grease screw 1 click (1/3 turn). Fill cavity when low (use white grease syringe). Push the red
indicating light to reset.
When refilling the grease, open air gap screw on top of the unit nearest to each grease port. Tighten
the green grease knob until the air pocket “burps” and then replace the screw. This pushes grease
into position ready for each maintenence click.
Top off water tank as necessary
If changing the water, use ½ ounce of Royal Purple ICE and regular 1 ounce of regulator antifreeze.
Fill with purified water, never use distilled water. Fill below water flume.

Summary of Contents for Super Charger













Reviews: