background image

9

12-Gauge 

Green  Wire:

  

                    

Starter Output

 

Con-

nection Required

.  

Connect the Green wire to the vehicle’s Starter wire. This 

wire will show +12 Volts only when the ignition key is in the “Start” position. This 

wire is also found in the ignition switch wiring harness (see diagram on previous 

page). Some vehicles have a second Starter wire known as a “Cold Start” wire. 

When this is encountered, an optional relay may be needed, configured to the 

3-pin Red port, to energize the second Starter wire (pages 22-23).

Note: 

If a security system is present which utilizes a starter interrupt circuit, the 

Green wire must be connected to the Starter Motor side of the interrupt.

12-Gauge 

Blue  Wire:                       

 Ignition Output

 

Con-

nection Required

.  

Connect the Blue wire to the vehicle’s Ignition wire (also 

known as “Primary Ignition”). This wire will show +12 Volts when the ignition key 

is in the “Run” and “Start” positions and no voltage in the “Off” and “Accessory” 

positions. This wire is found in the ignition switch wiring harness (see diagram 

on previous page). 

Note:

 If two or more Primary Ignition wires are present, you will need to connect 

an optional relay or relays to the 3-pin Red port (see pages 22-23). 

Summary of Contents for RS-3A





























Reviews: