background image

 

 

Installation Instructions 

• 

With the rangehood unpackaged, place the outlet spacer on top of the outlet hole, place the 

Ø180mm outlet on top of that, line up the mounting holes and fix in place using eight of the 

15mm screws.  

• 

If the outlet flaps are not installed, fix at the top of the outlet (these form a one-way valve that 

stops things from falling into the rangehood when it is not in operation).  

• 

As stated in the pre-installation instructions - always use the 2M Ø180mm ducting provided with 

these hoods. If required, the 180mm to 150mm adaptor can be fitted to the end of the 180mm 

ducting to allow for 150mm ducting exterior/wall outlet.  

• 

The rangehood must be installed at the correct distance above the cooktop (650mm minimum 

from the cooking surface, 800mm recommended maximum). Measure up from the top of the 

cooktop the desired height & draw a horizontal line. 

• 

From this line, measure up 600mm and draw a second horizontal line for the main mounting 

screws.  

• 

Mark the centre point on this line and use the mounting bracket to mark the other two screw 

positions ~132mm either side.  

• 

For a brick or concrete wall, drill in the two holes ~40mm deep.  

• 

Fit the wall plugs and attach the mounting bracket (hooks up) using the three supplied 40mm 

screws.  

• 

Lift the rangehood onto the bracket hooks and check for strength.  

• 

If good, fit the remaining 15mm screw into the hole right of centre on the bracket, ~4 turns (this 

will help prevent the rangehood from being accidentally removed). 

• 

Fit the ducting to the outlet and secure in place with the supplied 4mm screws.  

• 

Lift the inner chimney to the ceiling and screw into position using the two 7mm screws (if this is 

not sufficient, the use of hollow wall anchors or spring toggle screws is recommended).  

• 

Check that the rangehood is secured and connect to the power supply. 

• 

The long oil collector clips to the bottom back edge of the rangehood. 

*If the wall is not brick or concrete, an alternate mounting method must be determined. 

 

 

Summary of Contents for ORC916MB














Reviews: