background image

 

 

      

LUBRICATION OF THE GAS TAPS  

This can only be performed by an authorized person. It may be required if the gas taps become stiff and 

difficult to turn. 
 

 

LEAK TESTING 

1.

 

Make sure gas control knobs are Off and turn the cylinder valve On. 

2.

 

Check for leaking joints by brushing with solution of half-liquid detergent and half water.  If a leak is 
present, bubbles will appear (or you may hear a hissing sound).  Retightening connections can generally 

repair a leaking joint.  You must also check the gas hose and connection at the gas cylinder.  If a leak 
cannot be resolved, do not proceed. 

 

DO NOT USE NAKED FLAME FOR LOCATING GAS LEAKS. 

IF A LEAK PERSISTS CALL AN AUTHORISED GAS FITTER. 

 
 
 

ELECTRICAL CONNECTIONS 

 

 

LOCAL AUTHORITY REQUIREMENTS 

Installation is only permitted by an authorized person, and carried out according to instructions provided by the 

manufacturer.  Incorrect installation might cause harm and damage which the manufacturer accepts no 
responsibility.  The electrical connection can be found centrally along the back rear edge of the appliance. 
 

INSTALLATION 

This cooktop must be connected to a 220-240V 50Hz power supply. It is earthed via the cord. 
Before carrying out the connection to the power supply, the voltage rating of the appliance (stamped on the 
appliance identification plate) must be checked for correspondence to the available mains supply voltage, and 
the mains electric wiring should be capable of handling the hob’s power rating (also indicated on the 

identification plate); 
The power point must be connected to a suitable earth wiring, in conformity to current safety regulations. 
Ensure that the power supply is within 900mm of the cooktop. The power supply cord must not touch against 

any hot surfaces and must be placed so that its temperature does not exceed 75 degrees C at any point along 
its length. 
The colours of the wires in the hob power cable may not correspond with the colours marked on the terminals 

of your electrical plug .The plug should in any case be wired as follows:   
—connect the green/yellow wire to the terminal marked with the letter E or the earth symbol or coloured 
green/yellow; 

Summary of Contents for OCG61X













Reviews: