background image

2

 

INSTALLATION 

Unpacking the Appliance

 

Remove the external & internal packaging.  

When unpacking the appliance please check for any damage. If damage is found, do not connect to the power source and contact the 

Authorised Service Provider. Check that the following items are contained within the packaging: 

1 adjustable shelf

1 small glass shelf

Before connecting the appliance to the power source, let it stand upright for approximately 4 hours. This will reduce the possibility of a 

malfunction in the cooling system from handling during transportation. Remove any protective film from the outer surface. 

Clean the interior surface with lukewarm water using a soft cloth. 

Installing the Refrigerator 

This appliance is designed to be free standing only, and should not be recessed or built

in. 

Place your appliance on a solid, level floor that is strong enough to support the appliance when it is fully loaded. Use the adjustable feet at the 

bottom of the appliance to compensate for any unevenness of the floor.  

Allow at least 10 cm of space around the back and sides of the appliance, which allows the proper air circulation, and at least 20cm above the 

unit.   

Locate the appliance away from direct sunlight and sources of heat (stove, heater, radiator, etc.). Direct sunlight may affect the acrylic coating 

and heat sources may increase electrical consumption. Extreme cold ambient temperatures may also cause the appliance not to perform 

properly. Avoid locating the appliance in moist areas.   

Plug the appliance into an exclusive, properly installed

grounded wall outlet. Do not under any circumstances cut or remove the third (ground) 

prong from the power cord. Any questions concerning power and/or grounding should be directed toward a certified electrician or an Authorised 

Service Centre.  

After plugging the appliance into a wall outlet (220

240V 50Hz), allow the unit to cool down for 2~3 hours before placing food in the freezer and 

refrigeration compartments.  

If moving the appliance, avoid tilting the appliance more than 45°. At no time should the appliance be turned upside down. 

Adjusting the Door

 

The door can be adjusted to open from either the left or right hand side. Follow the instructions below (this is structured to transfer the door 

hinges from the right hand side to the left hand side):   

1.

Remove the upper hinge cover (6) and remove the upper hinge (5)

by unscrewing the two screws (1).

2.

Lift the door away and place in a safe position where it won’t get

damaged.

3.

Remove the lower hinge (2) by unscrewing the two screws (8).

4.

Remove the left leg (4) and fix it to the right hand side.

5.

Remove the screw hole cover (7) from the top left hand side and

place it on the top right hand side.

6.

Remove the lower hinge pin (9) and reverse the direction of the

lower hinge. Screw the lower hinge (2) back using the two screws (8)

to the lower left hand corner. Place the lower hinge pin back in to the

lower hinge.

7.

Place the door back onto the lower hinge pin. Place the upper hinge

(5) pin into the top of the door, even the door up to the top of the

appliance and fix the upper hinge in place using the two screws (1).

Place the upper hinge cover (6) over the upper hinge.

Summary of Contents for OBFD126X











Reviews: