background image

3

PRePARATIOn

Assembly

Always secure the handle into the handle sleeve with the bolt provided. Tighten securely to prevent accidental 

removal of handle while in use.

Before Use

1. 

Verify that the product and application are compatible, if in doubt call Omega Technical Service (888) 332-6419.

2. Before using this product, read the operator's manual completely and familiarize yourself thoroughly with the 

product, its components and recognize the hazards associated with its use.

3. To familiarize yourself with basic operation, turn the release valve (handle knob):

  a. Clockwise

 until firm resistance is felt to further turning. This is the ‘

CLOSed

’ release valve position used to 

      

raise

 the saddle.

  b. Counter-clockwise

, but no more than 1 turn from the closed position. This is the ‘

OPen

’ release valve 

      position used to 

lower

 the saddle.

4. With saddle fully lowered, locate and remove cover plate, then remove the vent screw. Check oil level. Proper 

oil level will vary from just covering the ram cylinder to 3/16" above it as seen from the oil filler hole. Reinstall the 

vent screw.

5. Ensure that jack rolls freely. Unlock the handle by pulling up on the handle position lock lever and rotating lever 

clockwise until it rests upon the lever bracket as seen below in Figure 1. Pump the handle or use the foot pedal 

to raise and lower the unloaded saddle throughout the lifting range before putting into service to ensure the pump 

operates smoothly. Replace worn or damaged parts and assemblies with Omega authorized replacement parts 

only. The foot pedal is for positioning the unloaded saddle to contact the lift point, at which time the handle must 

be used to raise the load. 

!

   

WARNING

•  

Study, understand, and follow

 all printed 

materials provided with/on this product 

before use

.

•  

do not

 exceed rated capacity.

•  Use 

only

 on hard, level surface.

•  

This is a lifting device only!

•  

Immediately

 after lifting, support the load with 

 

a pair

 of appropriately rated jack stands.

•  Lift 

only

 on areas of the vehicle as specified by 

the vehicle manufacturer.

•  

do not

 move or 

dolly

 the 

vehicle

 while on the jack.

•  No alterations shall be made to this product.

  

Failure to heed

 these markings may 

result

 in 

personal injury and/or property damage.

To avoid 

crushing and related injuries

:

• 

never

 work on, under or around a load supported 

only by hydraulic jack.

• 

Always

 use adequately rated jack stands.

• Chock each unlifted tire in both directions.

• 

do not

 use this device to lift, level, lower, support nor 

move a house, mobile home, travel trailer, camper or 

any building structure.

• 

Be alert

 and 

sober

 when using this product. Do not 

operate under the influence of drugs or alcohol.

!

   

WARNING

X

 

!

Always

 verify that the lift point is centered on saddle before lifting! 

Lift 

only

 on lift points authorized by the vehicle manufacturer. 

Summary of Contents for MagicLift 25057









Reviews: