background image

FOR 

WARRANTY

 RETURNS, please have 

the following information available BEFORE 

contacting OMEGA:

1.   Purchase Order number under which the 

product was PURCHASED,

2.   Model and serial number of the product 

under warranty, and

3.   Repair instructions and/or specific 

problems relative to the product.

FOR 

NON-WARRANTY

 REPAIRS, consult 

OMEGA for current repair charges. Have 

the following information available BEFORE 

contacting OMEGA:

1.               Purchase  Order  number  to  cover  the  COST   

 of the repair,

2.   Model and serial number of the product, and

3.   Repair instructions and/or specific problems  

relative to the product.

OMEGA’s policy is to make running changes, not model changes, whenever an improvement 

is possible. This affords our customers the latest in technology and engineering.

OMEGA is a registered trademark of OMEGA ENGINEERING, INC.

© Copyright 2016 OMEGA ENGINEERING, INC. All rights reserved. This document may not 

be copied, photocopied, reproduced, translated, or reduced to any electronic medium or 

machine-readable form, in whole or in part, without the prior written consent of OMEGA 

ENGINEERING, INC.

WARRANTY/ DISCLAIMER

OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and 

workmanship for a period of 

13 months

 from date of purchase. OMEGA’s Warranty adds 

an additional one (1) month grace period to the normal 

one (1) year product warranty

 to 

cover handling and shipping time. This ensures that OMEGA’s customers receive maximum 

coverage on each product. 
If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer 

Service Department will issue an Authorized Return (AR) number immediately upon phone 

or written request. Upon examination by OMEGA, if the unit is found to be defective, it 

will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply to defects 

resulting from any action of the purchaser, including but not limited to mishandling, 

improper interfacing, operation outside of design limits, improper repair, or unauthorized 

modification. This WARRANTY is VOID if the unit shows evidence of having been tampered 

with or shows evidence of having been damaged as a result of excessive corrosion; or 

current, heat, moisture or vibration; improper specification; misapplication; misuse or 

other operating conditions outside of OMEGA’s control. Components in which wear is not 

warranted, include but are not limited to contact points, fuses, and triacs.

OMEGA is pleased to offer suggestions on the use of its various products. 

However, OMEGA neither assumes responsibility for any omissions or errors 

nor assumes liability for any damages that result from the use of its products 

in accordance with information provided by OMEGA, either verbal or written. 

OMEGA warrants only that the parts manufactured by the company will be as 

specified and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR 

REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, 

EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY 

WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 

ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies of purchaser 

set forth herein are exclusive, and the total liability of OMEGA with respect to 

this order, whether based on contract, warranty, negligence, indemnification, 

strict liability or otherwise, shall not exceed the purchase price of the component 

upon which liability is based. In no event shall OMEGA be liable for consequential, 

incidental or special damages.

CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: 

(1) as a “Basic Component” under 10 CFR 21 (NRC), used in or with any nuclear installation 

or activity; or (2) in medical applications or used on humans. Should any Product(s) be 

used in or with any nuclear installation or activity, medical application, used on humans, or 

misused in any way, OMEGA assumes no responsibility as set forth in our basic WARRANTY/

DISCLAIMER language, and, additionally, purchaser will indemnify OMEGA and hold 

OMEGA harmless from any liability or damage whatsoever arising out of the use of the 

Product(s) in such a manner.

RETURN REQUESTS/ INQUIRIES

Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. 

BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN 

AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER SERVICE DEPARTMENT 

(IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then be 

marked on the outside of the return package and on any correspondence. The purchaser is 

responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in 

transit.  

Summary of Contents for HHM-NCV40

























Reviews: