background image

WARRANTY/DISCLAIMER

OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and 

workmanship for a period of 

13 months

 from date of purchase. OMEGA’s WARRANTY adds 

an additional one (1) month grace period to the normal 

one (1) year product warranty

 to 

cover handling and shipping time. This ensures that OMEGA’s customers receive maximum 

coverage on each product. 
If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer 

Service Department will issue an Authorized Return (AR) number immediately upon phone 

or written request. Upon examination by OMEGA, if the unit is found to be defective, it 

will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply to defects 

resulting from any action of the purchaser, including but not limited to mishandling, improper 

interfacing, operation outside of design limits, improper repair, or unauthorized modification. 

This WARRANTY is VOID if the unit shows evidence of having been tampered with or shows 

evidence of having been damaged as a result of excessive corrosion; or current, heat, moisture 

or vibration; improper specification; misapplication; misuse or other operating conditions 

outside of OMEGA’s control. Components in which wear is not warranted, include but are not 

limited to contact points, fuses, and triacs.

OMEGA is pleased to offer suggestions on the use of its various products. However,  

OMEGA neither assumes responsibility for any omissions or errors nor assumes 

liability for any damages that result from the use of its products in accordance 

with information provided by OMEGA, either verbal or written. OMEGA warrants 

only that the parts manufactured by the company will be as specified and free of 

defects. OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY 

KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE, AND ALL 

IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY AND 

FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION 

OF LIABILITY: The remedies of purchaser set forth herein are exclusive, and the 

total liability of OMEGA with respect to this order, whether based on contract, 

warranty, negligence, indemnification, strict liability or otherwise, shall not exceed 

the purchase price of the component upon which liability is based. In no event shall 

OMEGA be liable for consequential, incidental or special damages.

CONDITIONS:  Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) 

as a “Basic Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or 

activity; or (2) in medical applications or used on humans. Should any Product(s) be used in or 

with any nuclear installation or activity, medical application, used on humans, or misused in 

any way, OMEGA assumes no responsibility as set forth in our basic WARRANTY / DISCLAIMER 

language, and, additionally, purchaser will indemnify OMEGA and hold OMEGA harmless from 

any liability or damage whatsoever arising out of the use of the Product(s) in such a manner.

RETURN REQUESTS/INQUIRIES

Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. 

BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN 

AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER SERVICE DEPARTMENT 

(IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then be 

marked on the outside of the return package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to 

prevent breakage in transit. 

 

OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible.  

This affords our customers the latest in technology and engineering.
OMEGA is a trademark of OMEGA ENGINEERING, INC.
© Copyright 2018 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied, 

reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or in part, without 

the prior written consent of OMEGA ENGINEERING, INC.

FOR 

WARRANTY

 RETURNS, please have 

the following information available BEFORE  

contacting OMEGA:
1. Purchase Order number under which  

  the product was PURCHASED,
2.  Model and serial number of the product 

under warranty, and

3.  Repair instructions and/or specific  

problems relative to the product.

FOR 

NON-WARRANTY

 REPAIRS, consult 

OMEGA for current repair charges. Have the 

following information available BEFORE  

contacting OMEGA:
1.  Purchase Order number to cover the  

COST of the repair,

2. Model and serial number of the product, and
3. Repair instructions and/or specific problems  

  relative to the product.

Summary of Contents for FMA1800A





































Reviews: