Arming Using the Controller or Transmitter
The system can always be armed from the controller or transmitter, if the
ignition key is “off” and the system is not in the Valet Mode. To arm the system,
exit the vehicle, close all of the doors, and simply press and release the “arm/lock”
button once.
Your Crime Guard system is designed to deter theft of both your vehicle and its
contents. “Arming” your system turns on its protection, disabling the vehicle’s
starter and locking the doors. Once the system is Armed, any intrusion attempt will
Activate it, sounding the electronic “Psyren” psycho siren and flashing the parking
and interior lights to attract attention. The unique and patented “2-in-1” Psyren
psycho siren actually produces the sounds of two different sirens at once, ensuring
that it won’t be ignored like all of the other “common” car alarms. Disarming
the
system turns off the protection, unlocking the doors and turning on the parking and
interior lights, allowing lighted access to, and normal use of, the vehicle.
There are two methods of arming the Crime Guard:
1-
The first method is to use the controller* or transmitter, by pressing and
releasing the “arm/lock” button. The system must not already be armed or be
in Valet Mode, and the vehicle’s ignition key must be off.
2-
The second method is Last Door Arming, which configures the system to
automatically arm itself every time you exit the vehicle. This method of arming
is programmable, and may be used or not used as desired.
Using the Crime Guard System
Regardless of how it became armed, if the system is armed the window unit’s Status
Light flashes in the red color.
The system’s reaction:
The parking and interior lights will flash once, the siren
will chirp once and the Status Light will begin to flash red, confirming that the
system is armed.* In addition, the doors will lock and the starter interrupt will
engage to prevent any attempt to start the vehicle. Your security system is now fully
armed, and is ready to respond if an intrusion attempt is detected.
If the controller was used:
Immediately after the system responds the con-
troller will chirp twice (or four times if a zone is bypassed), the “ARM” icon will
appear, the “locked lock” icon appears, confirming that doors have locked, and the
number of operating transmitters or transceivers is briefly displayed.
Page - 7
*If the 2-way controller is used to operate the system, it will receive a signal
back and confirm that the operation was performed.
*The system is described in its most common and basic configuration, with
doorlocks connected, and he interior lights must be connected. The vehicle
horn may used in place of, or in addition to, the system’s electronic siren.
The Installer Programmable Features
The second group of features, the Installer Programmable Features, are accessed as
the second level of features’ programming, which is pressing the Valet Switch 10
times instead of 5 times when entering Programming Mode (page 28). Caution:
These features have a critical affect upon the system’s operations, and in many
cases, also upon the system’s wiring connections. These features should
NEVER be changed, except by the installer or other qualified professional.
The companion Installation Instructions booklet should be consulted for wiring
connections associated with these features.
The Crime Guard 850i
5
’s 10
Installer
Programmable Features
:
1
Doorlocking Functions
2
Light Relay Functions
3
Horn Relay Functions
4
Turbo Timer
5
Manual Transmission Remote Starting
6
“Tach Wire” or “Tachless” Starter Operations
7
Extended Starter Cranking Time
8
Programmable Remote Start Relay
9
Arm, Disarm or Additional Channels
10
Gasoline or Diesel Engine
Use the step-by-step instructions on pages 28-29 to change any of the Installer
Programmable Features, along with the feature’s option choices and related
programming controller/transmitter button assignment found in the following
individual feature descriptions.
Page - 38
Installer Programmable Features should only be used by the original
or other qualified installer, AND individual Installer Features should
only be used, where applicable, with the correct wiring connections.
Feature #1 Doorlocking Functions
Factory Default Setting
.8 Second Lock & Unlock Output
(
press
“arm/lock” button to program
)
Options:
3 Second Lock & Unlock Output (
press
“disarm/unlock” button to program
)
Double Pulse Unlock Output
(
press
“
II
” button to program
)
Total Closure Lock Output
(
press
“
III
” button to program
)
This single feature gives the installer several needed options, to match the 850i
5
’s
doorlocking outputs to suite different vehicle requirements.
