CL1600 Programmer Software
Overview
The CL1600 Surface Probe Tester ships from the factor
with a copy of the Omega Programmer software. This is
an easy to use software package, especially written for
the CL1600. Only on instrument can run this software in
one computer at a time.
Program Installation
It is advisable to have your IT Department install this
software into your computer. Always back-up your
system before attempting to install this or any other
software package into your computer. Assuming you
have backed up your computer files, run the install
program. This program will run trouble free with
Windows
®
95, 98, ME, NT, 2000
Main Display
Main Screen
1. These are two analog gauges and corresponding
digital display windows; one is red to indicate process
temperature, the other is green to indicate set point
temperature.
2. The graph tracks the set point and process values
3. The change temperature wheel will allow rough
temperature setting between 45 to 450°C. Below it
there is a fine tune up and down arrow that allows
for fine tune setting in increments of 0.1 degrees.
To the right there is the FIND button. Pressing this
button will start tracking the set temperature on the
controller.
4. The Preset Setpoint buttons allow you to change the
setpoint temperature to pre-defined values ranging
from 45 to 450°C.
5. The QUIT button to exit the application.
ARTWORK/PRODUCT ART/
DWGS/START HERE ARROW
5
ARTWORK/PRODUCT ART/
DWGS/START HERE ARROW
6
CL1600-120VAC
CL1600-240VAC
Surface Probe Tester
omega.com [email protected]
®
Servicing North America:
U.S.A.:
OMEGA Engineering, Inc., One Omega Dr.
P.O. Box 4047, Stamford, CT 06907-0047 USA
Toll-Free: 1-800-826-6342 (USA & Canada Only)
Customer Service: 1-800-622-2378 (USA & Canada Only)
Engineering Service: 1-800-872-9436 (USA & Canada Only)
Tel: (203) 359-1660
Fax: (203) 359-7700
e-mail: [email protected]
For Other Locations Visit omega.com/worldwide
The information contained in this document is believed to be correct, but
OMEGA accepts no liability for any errors it contains, and reserves the right to
alter specifications without notice.
WARNING: These products are not designed for use in, and should not be used
for, human applications.
MQS4593/1213
Settings
Settings Screen
SOUND:
Will allow audible indications while monitoring.
Selections: ON, OFF
COM Port:
Selects the communication port to be used while
monitoring.
Selections: COM1, COM2, COM3, or COM4
Default: COM1
DECIMAL POINT:
Selects the decimal point accuracy for the readouts.
Selections: ONE, NONE
Default: ONE
TEMPERATURE UNITS:
Selects units of temperature to display on readouts.
Selections: CELCIUS, FAHRENHEIT
Default: CELCIUS
SKIP LOGO INTRODUCTION:
Selecting this box will cancel the logo introduction when
the program is activated from your desktop.
LOG TO FILE:
Selecting this box will allow data login. This command
is inactive at this time.
CHART TIME BASE:
Allows user to set the horizontal time graph display.
Selections: 1 minute, 10 minutes, or 1 hour
AUTOMATIC SCALING:
Selecting this box will pre-select a vertical scale which
varies according to temperature setting.
Un-selecting this box, will allow user to set up values to
zoom-in closer to the desired temperature range.
For complete product manual:
www.omega.com/manuals/manualpdf/M4593.pdf
1
3
4
5
2
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects
in materials and workmanship for a period of
13 months
from
date of purchase. OMEGA’s WARRANTY adds an additional one (1)
month grace period to the normal
one (1) year product warranty
to cover handling and shipping time. This ensures that OMEGA’s
customers receive maximum coverage on each product.
If the unit malfunctions, it must be returned to the factory for
evaluation. OMEGA’s Customer Service Department will issue an
Authorized Return (AR) number immediately upon phone or written
request. Upon examination by OMEGA, if the unit is found to be
defective, it will be repaired or replaced at no charge. OMEGA’s
WARRANTY does not apply to defects resulting from any action of
the purchaser, including but not limited to mishandling, improper
interfacing, operation outside of design limits, improper repair,
or unauthorized modification. This WARRANTY is VOID if the unit
shows evidence of having been tampered with or shows evidence of
having been damaged as a result of excessive corrosion; or current,
heat, moisture or vibration; improper specification; misapplication;
misuse or other operating conditions outside of OMEGA’s control.
Components in which wear is not warranted, include but are not
limited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various
products. However, OMEGA neither assumes responsibility for
any omissions or errors nor assumes liability for any damages
that result from the use if its products in accordance with
information provided by OMEGA, either verbal or written.
OMEGA warrants only that the parts manufactured by the
company will be as specified and free of defects. OMEGA
MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF
ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT
THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING
ANY WARRANTY OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.
LIMITATION OF LIABILITY: The remedies of purchaser set forth
herein are exclusive, and the total liability of OMEGA with
respect to this order, whether based on contract, warranty,
negligence, indemnification, strict liability or otherwise,
shall not exceed the purchase price of the component upon
which liability is based. In no event shall OMEGA be liable for
consequential, incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used,
nor shall it be used: (1) as a “Basic Component” under 10 CFR 21 (NRC),
used in or with any nuclear installation or activity; or (2) in medical
applications or used on humans. Should any Product(s) be used in or
with any nuclear installation or activity, medical application, used on
humans, or misused in any way, OMEGA assumes no responsibility
as set forth in our basic WARRANTY/DISCLAIMER language, and,
additionally, purchaser will indemnify OMEGA and hold OMEGA
harmless from any liability or damage whatsoever arising out of the use
of the Product(s) in such a manner.
RETURN REQUESTS/INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA
Customer Service Department. BEFORE RETURNING ANY
PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN
AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER
SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING
DELAYS). The assigned AR number should then be marked on the
outside of the return package and on any correspondence.
FOR
WARRANTY
RETURNS,
please have the following
information available BEFORE
contacting OMEGA:
1. Purchase Order number under
which the product was
PURCHASED,
2. Model and serial number of
the product under warranty, and
3. Repair instructions and/or
specific problems relative to
the product.
FOR
NON-WARRANTY
REPAIRS,
consult OMEGA for current repair
charges. Have the following
information available BEFORE
contacting OMEGA:
1. Purchase Order number to
cover the COST of the repair or
calibration,
2. Model and serial number of the
product, and
3. Repair instructions and/or specific
problems relative to the product.
OMEGA’s policy is to make running changes, not model changes,
whenever an improvement is possible. This affords our customers
the latest in technology and engineering.
OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2013 OMEGA ENGINEERING, INC. All rights reserved.
This document may not be copied, photocopied, reproduced,
translated, or reduced to any electronic medium or machine-readable
form, in whole or in part, without the prior written consent of OMEGA
ENGINEERING, INC.
