background image

CLEANING INSTRUCTION

Blender container parts are corrosion resistant, sanitary and easily cleaned. Do not
put the container assembly & blender base assembly in the dishwasher.

1.Before first use and after every use, separate container parts from the base.

2.Add  cleaning  solution  to  the  container.  Use  washing  solution  of  tepid  water  (less  than
115°F/46°C) and a non-sudsing detergent. Use the recommended amount of detergent.

3.Scrub and flush out the container interior lid and feeder cap to remove food residue. Empty
container.

4.Fill container 1 /4 full with fresh washing solution and place it on the base.

5.Replace the lid on the container and run the blender on  high speed for 2 minutes.

6.Repeat step 4 using clean rinse water (95°F/35°C).

7.Wipe down the container, feeder cap, and lid with a soft cloth or sponge, dampened with
fresh washing solution.

8.Wipe the exterior of the base with a damp cloth or sponge. The base contains electrical
components: do not immerse, use a high-pressure washer, or use a dishwasher to clean the
base.

CARING TIPS

To care for your blender, please read the tips as follows:

1.Periodically check all parts before reassembly. As use of damaged or non-recommended
parts could result in a severe personal injury and/or damage to the blender

2.Blades:
If the processing blades are stuck or difficult to turn, 

DO NOT USE BLENDER

(Check by

carefully turning the blades in a counterclockwise direction, where the opposite edges are
sharp. Blades should turn freely.) 

3.Container:
If  the  Eastman  Tritan  container  is  cracked, 

DO  NOT  USE  BLENDER

,  further  use

could result in the container breakage during use. 

4.Blender Base:
Never immerse the blender base in water. Unplug unit. The housing can be cleaned with a
damp cloth.

5.Motor:
The motor is permanently lubricated and does not require any additional lubrication.

Omega BL330 series manual:Layout 1  4/2/12  10:13 AM  Page 6

Summary of Contents for BL330 series









Reviews: