3
2
SPECIFICATIONS
Model
Capacity
Base Size
Min. Height
Max. Height
23226
22 Ton
19-3/4” x 61-5/8”
10-5/8”
19-5/8”
SAFETY AND GENERAL INFORMATION
Save these instructions.
For your safety, read, understand, and follow the information provided with and on this
device before using. The owner and/or operator shall have an understanding of the device, its operating characteristics
and safety operating instructions before operating the equipment. The owner and/or operator shall be aware that use
and repair of this product may require special skills and knowledge. Instructions and safety information shall be read
to and discussed with the operator in the operator's native language, making sure that the operator comprehends
their contents, before use of this equipment is authorized. If any doubt exists as to the safe and proper use of this
device, remove from service immediately.
Inspect before each use.
Do not use if abnormal conditions such as cracked welds, damaged, loose or missing
parts are noted. Any equipment that appears damaged in any way, is found to be worn, or operates abnormally shall
be removed from service until repaired. If the equipment has been or is suspected to have been subjected to an
abnormal load or shock, immediately discontinue use until inspected by a factory authorized repair facility (contact
distributor or manufacturer for list of authorized repair facilities). It is recommended that an annual inspection be
made by an authorized repair facility. Labels and Operator's Manuals are available from the manufacturer.
PRODUCT DESCRIPTION
Hydraulic Truck Jacks are designed to lift, but not support, rated capacity partial vehicle loads consisting of one end
of a vehicle. Immediately after lifting, support loads with a matched pair of appropriately rated jack stands.
PREPARATION
Reference Replacement Parts pages 6 and 7 for parts location & assembly sequence. Assemble, align and insert
the handle assembly and handle position bar into the handle sleeve, then tighten the bolt on handle sleeve to prevent
accidental removal of handle while in use.
Before Use
1. Verify that the product and application are compatible, if in doubt call Omega Lift Technical Service (888) 332-6419.
2. Before using this product, read the operator's manual completely and familiarize yourself thoroughly with the
product, its components and recognize the hazards associated with its use.
3. To familiarize yourself with basic operation, locate and turn the release valve (handle knob):
a.
Clockwise
until firm resistance is felt to further turning. This is the ‘
CLOSED
’ release valve position used to
raise
the load.
b.
Counter-clockwise
, no more than 1 full turn from closed position. This is the ‘
OPEN
’ release valve position
used to
lower
the load. The further the release valve is turned counter-clockwise, the faster the load descends.
4. With ram fully lowered, remove the oil filler screw. Check oil level. Proper oil level should be just below the rim of
the opening. Reinstall the oil filler screw.
5. Pour a teaspoon of good quality air tool lubricant into the air supply inlet of the lift control valve. Connect to air
supply, then squeeze the lift control valve for 3 seconds to evenly distribute lubricant.
NOTICE:
These models are equipped with 1/4" NPT air couplers. If installing a different air coupler, ensure thread
tape or compound is used on connections. To ensure dependable, trouble free operation an inline air dryer and oiler
is recommended.
6. Ensure that jack rolls freely. Raise and lower the unloaded ram throughout the lifting range before putting into
service to ensure the jack operates smoothly. Replace worn or damaged parts and assemblies with Omega
authorized replacement parts only.
Bleeding/Venting Trapped Air
1. Open oil filler plug.
2. Open release valve.
3. Activate air motor to vent air.
4. Remove set screw and use a screw driver to hold down check ball while very slowly pumping air motor until oil
exiting from screw hole is steady without bubbles.
5. Reinstall set screw approximately two turns into hole (do not fully tighten).
6. Activate air motor a few additional times to vent air, while slowly tightening set screw. Ram should start to raise
as screw is fully tightened.
7. Check oil level and reinstall filler plug.
Figure 1 - Model 23226 Nomenclature
• Study, understand, and follow all
instructions
before operating this device.
• Do not exceed rated capacity.
• Use only on hard, level surface capable of
supporting the load.
• Lifting device only. Immediately after lifting,
support the vehicle with appropriate means.
• Do not move or dolly the vehicle while on the jack.
• Lift only on areas of the vehicle as specified by
the vehicle manufacturer.
• No alterations shall be made to this product.
• Failure to heed these markings may result in
personal injury and/or property damage.
To avoid crushing and related injuries:
•
Never work on, under or around a load supported
only by hydraulic jack.
• Always use adequately rated jack stands.
• Chock each unlifted tire in both directions.
• Do not use this device to lift, level, lower, support nor
move a house, mobile home, travel trailer, camper or
any building structure.
• Be alert and sober when using this product. Do not
operate under the influence of drugs or alcohol.
X
File name: A2102_1706OUT
Date: 2017.06.08
Drawn By: 黃家威
Checked By:
Approved By:
Model No. A2102
Lift Control
Valve
Handle Position
Release
Handle Knob
(release valve)
Air Supply Inlet,
1/4NPT
Handle
Wheel
Saddle
WARNING
!
WARNING
!
