Omarv Bologna 320 Handbook Download Page 15

BOLOGNA 

- FLY MOWER

15

“Warning!

The machine must be operated by a single operator and authorized, trained and appropriately trained personnel.

Use other than the specified one is considered improper. Make a check of the machine and the handle before each commissioning.

The manual must always be within reach so that it can be consulted to check the operating cycle. If lost or damaged, the replacement copy must be 

requested from Omarv Srl. Never work with this machine if you are tired, sick or under the influence of alcohol, drugs, or medicines.

It is recommended that the operator of the machine does not wear garments that may give rise to catches (sleeves without closed wrist, belts, 

necklaces, bracelets, rings). It is absolutely forbidden to get up or get out of the car. In order to avoid ingestion, it is necessary to proceed at regular 

speed during processing, as if the speed is too high, the shredded product can not be ejected properly. The feed rate must be proportional to the 

amount of product to be trimmed and to the power of the tractor. Do not interrupt, for any reason, between the tractor and the shredder with a powe-
red engine and a power take-off.“

Once the working area has been reached, the three trimming members (A) (B) and (C) must be lowered, insert

The p.d.p. And slowly start the shredder. Proceed for a few meters, check it out

The feed rate based on soil conditions and the product to be trimmed, and possibly adjust the working height.

“Warning!

Lower the shaving organs making sure the ground is

Flat and that there are no people, things or animals
Within the range of the machine. “

“Beware!

For proper use of the machine, it is necessary to adjust the working 

height so that the trimmer tools touch the ground without touching it. “

To adjust the rear roller act on the bolts (D) on both sides of the machine.

“Warning!

Before making the adjustments, you have to wait until the tools

Have not run out the residual centrifugal force to avoid the danger of
injury. “

The quality of work and the required power are in operation:

• the type of product to be crushed and its moisture;

• the type of knives used;

• working height;

• the tractor’s forward speed;

Choice of knives to use.

The machine is equipped with standard hammers that offer excellent cutting and ventilation quality. These hammers are 

ideal for uncultivated soil, grass, potatoes, beetroot leaves or carrots. Optional Y-recommended knives for corn, straw or rape 

are provided.

“Warning!

Only use original OMARV knives.”

Summary of Contents for Bologna 320




















Reviews: