background image

4

Do not look directly at the light from the LED light source for a long time.

The LED built in the LED lamp house (separately available) is basically eye-safe. However, do not look directly at the 
light from the LED lamp house for a long time, since it may cause damage to your eyes.  
If the laws or regulations for workers health and safety have been established, follow them when using the 
microscope.

Do not look directly at the light coming out from the objective or the specular reflection light from the 
specimen.

Do not look directly at the light coming out from the objective for a long time, since it may cause damage to your 
eyes.

Do not expose your skin to the light coming out from the objective for a long time.

If your skin is exposed to the light coming out from the objective for a long time, you may get burned. 

 CAUTION  - Protection of electrick shock -

 CAUTION  - LED (light emitting diode) -

Keep the power cord and cables sufficiently away from the lamp housing.

If the power cord and cables contact a hot area of the lamp housing, they could melt and cause electric shock.

Summary of Contents for BX3M-PSLED

























Reviews: