background image

 

Complete Teardown, Cleaning, and Reassembly of the Olympus BH2-BI30 Binocular Viewing Head

 

(

Rev. 1)

 

Page 25 of 34

 

hand  (see 

Figure  92

)  and  left-hand  (see 

Figure  93

ocular slides. 

 

Figure 92 – Apply grease to rear bearing surfaces (right) 

 

Figure 93 – Apply grease to rear bearing surfaces (left) 

Reinstall the Ocular Slide Assembly (Left) 

Carefully place  the  left-hand ocular slide  assembly  into 
position  on  the  front  frame,  making  sure  the  lower 
beveled edge seats into the beveled dovetail channel in 
the  bottom  of  the  frame  (see 

Figure  94

),  and  that  the 

index pin in the index arm engages with the lower slot 
in  the  brass  pivot  lever  (see 

Figure  95

).    Be  extremely 

careful  during  this  process  to  neither  scratch  nor 
smudge the P6 prism in the process. 

 

Figure 94 – Seat lower bevel into the bottom dovetail (left) 

 

 

Figure 95 – Index pin engaged with brass pivot lever (left) 

Apply  a  light  coating  of  a  suitable  grease  (item  5  of 

Appendix 1

to the upper bevel of the left-hand ocular 

slide (se

Figure 96

).  

 

Figure 96 – Apply grease to the upper bevel (left) 

Place the left-hand dovetail block into position over the 
two  protruding  index  pins  on  the  front  frame  (see 

Figure 97

). 

 

Figure 97 – Place the dovetail block into position (left) 

Use  a  suitable  JIS  screwdriver  to  reinstall  the  two 
M2.6x5 JIS screws to secure the left-hand dovetail block 
to the front frame (se

Figure 98

). 

Summary of Contents for BH2-BI30



































Reviews: