background image

Congratulations 

on your purchase of the 

Olympia 

RG245 CREE XPG LED 

high-performance, 

high durability flashlight. The Olympia brand is 

synonymous with integrity. Our word is our bond. 

As a result, this product is designed to provide you 

with the best possible functionality. Its innovative 

CREE XPG LED technology is geared for optimum 

effectiveness and high efficiency. Its ability to 

endure rugged use is enabled by the aircraft-grade 

aluminum with premium type III hard anodized 

anti-abrasive finish. This represents the industry’s 

top tier in durable finishes. It is lightweight and 

compact in design making it a great option for 

portability. Use it in any situation - hunting, hiking, 

camping, caving, general household, recreational 

activities, rugged sports, industrial worksite or 

emergency situations. Please take a few moments 

to read this user guide to ensure that you get the 

best performance and years of trouble-free use.

Product Description

Battery Installation

1.  Unscrew the tail switch cap and insert 

1*CR123 rechargeable (NiMH) *battery. The (+) 

terminal on the batteries should face toward 

the flashlight’s head.

2. Replace the tail switch cap and be sure to 

tighten snugly, but do not over tighten as this 

could strip the threads in the cap. Turn on the 

flashlight as indicated in any of the options 

listed in the table that follows. 

Note: If the tail 

cap is not tightened snugly, the flashlight 
will not turn on.

3. When the battery life is nearly depleted, your 

flashlight will blink to indicate new batteries are 

needed.

Flashlight Operation

Your 

Olympia RG245 CREE XPG LED

 high-

performance, high durability flashlight has a 

push-button tail switch for on/off operation and is 

equipped with 1) Momentary and 2) Continuous 

light options. It also has 5 illumination light modes 

to suit your varied needs. See table instructions 

that follow to access these functionalities:

Olympia RG245
CREE XPG LED  
Flashlight

User Guide

Lighting Operation Modes

Momentary-on 

Lighting

Press the push-button tail switch 

half-way to activate the light 

momentarily.

Continuous 

Lighting

Press the tail switch push-button to 

completely turn on the flashlight. 

The light will stay on until the push-

button is turned off.

Lighting Modes

There are five types of light output:

High

Middle

 

Low

Strobe

SOS

Press the tail push-button to switch 

to each mode

Accessing the 5 Lighting Modes

High Beam

Press the push-button tail  

switch once

Mid

Press the push-button tail  

switch twice

Low Beam

Press the push-button tail  

switch 3 times

Strobe

Press the push-button tail  

switch 4 times

SOS

Press the push-button tail  

switch 5 times

Memory function

Your 

Olympia RG245 CREE XPG LED

 

high-performance, high durability flashlight 

automatically memorizes the last light setting/

mode used when the flashlight next is turned on. 

i.e., after being in any one of the five light settings 

(High

Middle

Low

Strobe

SOS) for 3 

seconds, the last one used will be memorized.

Maintenance and Precautions

1.  Do not disassemble the sealed head. Doing 

so can cause damage to the flashlight and will 

void the warranty. 

2. Use high-quality batteries or you run the risk 

of the flashlight being damaged by electrolyte 

leakage or battery breakage.

3. If the flashlight will not be used for a long time, 

remove the batteries to avoid damage caused 

from battery leakage.

4. Lubricate the O-rings regularly using a 

Q-Tip

®

.  Apply a small dab of silicone grease 

or petroleum jelly to the contacts to prevent 

corrosion. Doing so will keep the flashlight 

properly sealed against water. If the O-rings are 

damaged after prolonged use, replace them.

5. Clean the flashlight contacts periodically 

especially if the light flickers or does not light 

up. There are different reasons for a flickering or 

non-working light:
A: The batteries may need to be replaced. 

Solution: Replace old/defective batteries with 

new ones (be sure to double check correct 

installation of + and - terminals).

B: The threads, PCB board contact or other 

contacts are dirty. 

Solution: Use a Q-Tip

®

 to apply a tiny amount 

of alcohol to clean the contact points.

If the above methods do not work, please refer to 

the warranty policy listed in this user guide.

Switch

Tail

Cap

Clip

Lanyard

Hole

Body

Head

Reviews: