The light source of this luminary is not replaceable when the light source reaches its end of life the
whole luminary shall be replaced.
ATTENTION!!!
1
2
4
5
KLD-30/ST/ADR
KLD-30/ST/ADR
KLD-22/ST/ADR
KLD-22/ST/ADR
KLR-20/ST/ADR
KLR-20/ST/ADR
Legend installation-replacement
PC, Acrylic Plate
560gr.
955gr.
740gr.
KLD-22/ST/ADR & KLD-30/ST/ADR
KLR-20/ST/ADR
1
3
2
4
European
manufacturers
Olympia Electronics - European manufacturer
Thank you for your trust in our products
NOTE:
LED=
Light Emitting Diode
LABELING EXPLANATION:
X:
Self contained
1:
Maintained
(*)
180:
3 hours duration
F:
Automatic test gear complying with IEC 61347-2-7 denoted EL-T
C:
Including inhibiting mode
E:
With non-replacable lamp(s) and/or battery
G:
Internally illuminated safety sign
A:
Including test device
B:
Including remote test mode
60:
1 hour duration
480:
8 hours duration
Non Maintained operation: The luminary lights its illumination source, only in mains power supply’s failure.
(*) Maintained operation: The luminary lights its illumination source, when it is powered by the mains power
supply or not.
KLD-30/ST/ADR, KLD-22/ST/ADR
& KLR-20/ST/ADR
KLD-30/ST/ADR
KLD-22/ST/ADR
KLR-20/ST/ADR
922502054_09_003
922502054_09_003
IP54
250/110/15lm
Light output
1h/3h/8h
Duration
30m
22m
20m
M
Maintained
Non
maintained
ΝΜ
Warranty
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of
warranty is specified in the official catalogue of Olympia Electronics and also in the technical
leaflet, which accompanies each product. This warranty ceases to exist if the buyer does not
follow the technical instructions included in official documents given by Olympia Electronics or if
the buyer modifies the goods provided or has any repairs or re-setting done by a third party,
unless Olympia Electronics has fully agreed to them in writing. Products that have been damaged
can be returned to the premises of our company for repair or replacement, as long as the
warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not
charge the buyer depending on the reason of defection. Olympia Electronics reserves the right to
charge or not the buyer the transportation cost.
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.com
220-240V AC / 50-60Hz
3.9W / 4.4VA
2
2
0.08mm - 1.5mm
39V DC
1h: 3.4, 3h: 1.4, 8h: 0.2
130mA
1.5W
20mA
Olympia Electronics S.A.
11.2-13.2V DC
0.72
2711195
Built-in main board
45 °C max. across the board
Technical Characteristics
LED Characteristics
MANUFACTURER
MODEL NUMBER
VOLTAGE RANGE
CONNECTIONS
NOMINAL POWER
TEMPERATURE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
3.6V/1.5Ah
20 - 120mA
0.87
BATTERY (Ni-MH)
INSULATION BETWEEN SUPPLY & CONTROL TERMINALS
INSULATION BETWEEN SUPPLY & BATTERY CIRCUIT
MINIMUM POWER FACTOR
WIRE CROSS SECTION
EMERGENCY OUTPUT FACTOR (EoFx)
MAX OPEN CIRCUIT VOLTAGE
Irated
Prated
U-OUT
SUPPLY CURRENT
Basic insulation
Basic insulation
BATTERY PROTECTION
1h / 3h / 8h Manually Selected (Default 3h)
CHARGE TIME
MINIMUM DURATION
24 hours
LED Charge, Lamp Fault LED, Battery Fault LED / Test Button
80lm / 1h: 250lm, 3h: 110lm, 8h: 15lm
LIGHT SOURCE LUMINOUS FLUX (MAINS / EMERGENCY)
INDICATIONS
MAX CHARGE VOLTAGE
MIN MAX. CHARGE CURRENT
TRICKLE CHARGE VOLTAGE/CURRENT
MIN MAX. DISCHARGE CURRENT
MIN MAX. DISCHARGE VOLTAGE
3 - 4.5V
4.9V
4.4V / 40mA
Deep discharge and overcharge protection / the control gear will recharge the battery normally after the test of 22.3
IP54
DEGREES OF COVER PROTECTION
EN 60598-1, EN 60598-2-22, ΕΝ 55015,
ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
PRODUCED IN ACCORDANCE WITH
OPERATION TEMPERATURE RANGE
CONTROL GEAR MAX.TEMPERATURE: tc
o
5 to 40 C
o
58 C at BR1
PC
RELATIVE HUMIDITY
CONSTRUCTION MATERIAL
EXTERNAL DIMENSION (L x W x H)
WEIGHT
GUARANTEE
Up to 95%
3 years (1 year for the battery)
CONTROL GEAR WITH AUTOMATIC
TEST FUNCTION
260x35x170mm
260x35x180mm
310x35x216mm
Accessories for installation
(After request)
Α-2130: Accessory for ceiling (1m)
Α-2131: Accessory for ceiling (0,5m)
Α-2132: Accessory for ceiling (0,25m)
Α-2133: Accessory for wall mounting
Α-2136: Accessory for hanging installation (2,5m)
A-2520/PL/ST: Suspended ceiling base
Battery replacement
3. Install a new battery of the same type and rating.
4. Assemble the luminary and power the device.
1. Disassemble the luminary.
2. Remove the battery connector and carefully remove the battery from its base.
70V
1h (400-690mA), 3h (190-295mA), 8h (55-95mA)
LED / CONSTANT CURRENT
LIGHT SOURCE / OUTPUT MODE
Addres-
sable
ADR
ADDRESSABLE SELF TESTING MAINTAINED
EMERGENCY ILLUMINATION SIGNS
X 1
8 0
1
A B
E
C
F G