Page
1
from 4
923193901_09_008
GENERAL
These luminaires are used in places where
emergency luminaires are needed.
E a c h l u m i n a i r e m u s t b e p e r m a n e n t l y
connected to mains power supply
.
In normal operation (L1 connected to L) the
led strip lights and the battery is charging.
In case of a mains power supply failure
t h e l u m i n a i r e w i l l n l i g h t t h e l e d s t r i p
automatically in emergency mode (powered by
its battery). When the mains power supply
is restored the device turns to normal
operation.
INSTALLATION
To install the luminaire follow the installation
instructions on page 3.
Battery Charging
The battery charging is completely controlled
.
Thereby,
the
best
possible
battery
maintenance is
achieved
,
as well as the
elongation of its duration
.
When the battery
has completely charged
,
it charges with a
maintenance current.
Battery Cut-off
The luminaire enters in this operation when
the mains power supply fails
and battery has
lost its energy
.
During this operation the
luminaire enters the idle state
and battery
consumption is negligible, in order to be
protected from deep discharge.
Manual
Test
This test can be done by placing the test card
on the side of the indications (page 4) and
remove it instantly an operation test is
initiated. The light source and the emergency
circuit of the device is monitored. The manual
test can be conducted only if the main power
supply and the battery is connected. During
this test period all indication LEDs are OFF.
Automatic operational test
This test includes all the operations that
provide the manual test and is conducted
automatically every 15 days. In order to be
performed, the mains power supply and the
battery should be connected.
Automatic Autonomous Test
The Automatic Autonomous Test is conducted
and measures the device’s back up operation
and emergency duration. This test is
conducted automatically every 6 months
.
In
order to be performed, the mains power
WATERPROOF SELF TESTING MAINTAINED EMERGENCY LUMINAIRES WITH WHITE LEDs
220-240V AC/50-60Hz
4.5W / 4.9VA
TECHNICAL CHARACTERISTICS
(for LED MODULE Specs see page 4)
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERY
(
Ni-Cd
)
CHARGING TIME
INDICATIONS
BATTERY PROTECTION
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
ILLUMINATION (MAINS / EMERGENCY)
ILLUMINATION SOURCE
90min
24h
Charge, Lamp Fault, Battery Fault LED
From overcharge and deep discharge
IP 65
3.6V/3Ah
210lm / 210lm
30 white LEDs
EN 60598-1, EN 60598-2-22
, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
5 to 40 C
o
Up to 95%
3 years
(1
year for the battery
)
745gr.
3.4W / 3.8VA
3.6V/
0.6
Ah
105lm / 105lm
15 white LEDs
180min
5.3W / 5.6VA
3.3W / 3.7VA
3.6V/1.5Ah
105lm / 105lm
30 white LEDs
210lm / 210lm
15 white LEDs
595gr.
675gr.
3
13
x 118 x 66 mm
Bayblend FR3010
,
transparent
polycarbonate
Thank you for your trust in our products
Olympia Electronics - European manufacturer
GR-1938/15L
GR-1939/15L
GR-1939/30L
GR-1938/30L
