manualshive.com logo in svg

OLT GS84-S-FJ-Metal, Assembly Manual, Page: 35 / 39

Share
Download
OLT GS84-S-FJ-Metal Assembly Manual Download Page 35

74.

 To reduce possible water from penetrating into the window cavity, 

caulk gap on both sides of window opening prior to installing 

Window 

Insert.

  Position insert in cavity and screw with 

6 - 8  1 1/4” Screws

. 

On sides, make sure to screw insert into the thick butt of the siding only.

75.

 Once Insert is attached, 

caulk the “triangular gap” 
between the Insert’s outside 
flange and the siding. Also put 
a bead of caulking horizontally 
at top of window where the 
flange and siding meet. 
This additional caulking will 
also will reduce the chances  
of moisture entering into your 
shed.

Caulk 
gap.

Window 
frame.

 Siding Butt

Screw insert into 
bottom (thick) 
part of siding.

Thick butt of siding

Caulk 
gap.

Lower  
interior 
door stop.

73.

  Attach upper and lower 

Vertical Interior 

Door Stops

 as per 

Step 72

.  Position against 

door jamb and underneath upper door trim. Attach 
with 

4 - 1 1/2” Finishing Nails

 per piece. 

Complete both sides.

Door 
Jamb.

  Toll Free 1-888-658-1658              www.outdoorlivingtoday.com        [email protected]

Page 35

Summary of Contents for GS84-S-FJ-Metal








































Reviews:

No comments