OLT GardenSaver GS124-SLIDER-PLY-AK Assembly Manual Download

Page: 11 / 40

Bottom Wall Plate

You can find BR1 -
Square Drive Bit for
the screws in with the
Hardware Kit Bag.

Carefully lay

2AA

- Side/Rear Wall Panels

face

down. Position and attach

2AB - Bottom Wall

Plates

to bottom of wall studs of each wall panel

with

3 - 2 1/2” Screws

. Position so plates are flush

with framing. Complete 4 remaining solid walls.

Parts

2AA - Side/Rear Wall Panels

(45 1/2” wide x 75” high)

x 5

2AB

- Bottom Wall Plates

(1 5/8” x 2 1/2” x 45 1/2”)

x 5

Hardware

- 2 1/2” Screws

x 15 total

Ensure bottom plate
is flush side-to-side
with wall studs

Important:

Make sure all walls are aligned in their

upright position. If not, water may leak into your shed.
Unsure if panel is facing up or down?
Recently attached Bottom Plate is on bottom of panel.

Outside 2x3 framing of wall panel should
be positioned flush with the outside of
floor framing when properly aligned.

The side wall panels will sit even with the floor frame and the rear wall panels will be sandwiched

between the side wall panels. The floor plywood may be slightly recessed.

Note:

Siding will overhang the floor frame by approximately 3/4”.

Starting on one side, position a Solid Wall Panel on top of plywood floor. The Wall Panel bottom framing

will sit flush with the outside of the floor frame. Wall siding will overhang the floor.

Siding overhangs
floor frame by 3/4”

Floor plywood
may be slightly
recessed

Do Not Attach Walls
To Floor until Step 24.

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 11

Summary of Contents for GardenSaver GS124-SLIDER-PLY-AK









































Search results

Summary of Contents for GardenSaver GS124-SLIDER-PLY-AK

Reviews:

Related manuals for GardenSaver GS124-SLIDER-PLY-AK

Brands by name

Popular brands

OLT GardenSaver GS124-SLIDER-PLY-AK, Assembly Manual

Search results

Summary of Contents for GardenSaver GS124-SLIDER-PLY-AK

Reviews:

Related manuals for GardenSaver GS124-SLIDER-PLY-AK

Brands by name

Popular brands