OLT 12x8 Cabana Assembly Manual Download

Page: 9 / 39

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 9

Attach

Front Floor Runners

to completed floor frame with notch aligned

flush with corner of floor framing and edge overhanging front by 2”.
The overhanging edge of the front floor runners will be used later to support
the sliding door track. Attach with

6 - 2 1/2” Screws

per Runner.

Parts

Front Floor Runners

(1 1/2” x 5 1/2” x 68 3/16”)

x 2

Hardware

- 2 1/2” Screws

x 12 total

With Floor Runners attached, carefully flip the floor over and place on your foundation.

Caution:

you will need 2 people to assist you. Be careful when laying floor down not to bend or twist floor.

When in place, level floor completely.

Note:

The floor will be flipped over

and the floor runners will sit on your
foundation. It is important to note that

having a level foundation is critical

Choosing a foundation will vary
between regions.
See page 3 of this assembly manual
for more information on foundations.

Foundations

Attach

Floor Runners

to completed floor frame as shown

above. Make sure Runners are flush with side and rear of
floor framing but not overhanging. Use

6 - 2 1/2” Screws

per

Runner.

Parts

Floor Runners

(1 1/2” x 3 1/2” x 68 3/16”)

x 8

Hardware

- 2 1/2” Screws

x 48 total

Concrete Slab
Foundation

Summary of Contents for 12x8 Cabana








































Search results

Summary of Contents for 12x8 Cabana

Reviews:

Related manuals for 12x8 Cabana

Brands by name

Popular brands

OLT 12x8 Cabana, Assembly Manual

Search results

Summary of Contents for 12x8 Cabana

Reviews:

Related manuals for 12x8 Cabana

Brands by name

Popular brands