Okolab UNO-T Manual Download Page 63

Page: 63 / 73

Note

►

Auto turn on procedure

’s

description perfectly fits also to the Auto turn off procedure.

Status Overview

To open the

Status

page, press on the icon

as show in Figure 96 a.

Figure 96. How to enter the Status Overview page (a - b).

Note

►

This page contains data useful for technical/control reasons. In case you requested support from one

of Okolab engineers you may be asked for some of these data

Icon and Glance Mode View

UNO-CONTROLLER features two display modalities:

Icon mode

and

Glance Mode

, as shown in Figure 97 a

and b. You can swap between the two display modalities by pressing on icon

Figure 97. Icon Mode and Glance Mode (a

–

b).

Info page

Press the icon

to access the Info Page, as shown in Figure 98 a. This page contains the information

related to the UNO-CONTROLLER version (as shown in Figure 98 b).

Summary of Contents for UNO-T










































































Search results

Summary of Contents for UNO-T

Reviews:

Related manuals for UNO-T

Brands by name

Popular brands

Okolab UNO-T, Manual

Search results

Summary of Contents for UNO-T

Reviews:

Related manuals for UNO-T

Brands by name

Popular brands