Okolab UNO-T Manual Download Page 57

Page: 57 / 73

Figure 82. How to enter the Display menu (a

–

b).

8.2.8.1

Options

Press the

Options

icon

(see Figure 83 a) to enter the Display Options page. The Display Options menu

allows to set the time frame in which the minimum and maximum temperature values are collected.

To insert the time frame, press the

+ / -

icons or scroll the

Chart history length

bar (1 in Figure 83 b).

Note

►

The chart history value length is pre-set at 5 minutes.

Note

►

Recommended value for the chart history length is 60 or 120 minutes.

To change the sound frequency, press the

+ / -

icons or scroll the

Buzzer frequency

bar

(2 in

Figure 83 b),

then press

Save

(4 in Figure 83 b) to confirm.

Note

►

To activate a sound at each touch, flag the Touch Buzzer checkbox (3 in Figure 83 b).

Figure 83. Settings

–

Display - Options (a

–

b).

8.2.8.2

Brightness

Press the icon

(see Figure 84 a) and scroll the bar (1 in Figure 84 b) or press the

+ / -

icons in the

page that opens to modify display

Brightness

. Set the required configuration and press

Save

(2 in Figure 84 b) to

confirm.

Summary of Contents for UNO-T










































































Search results

Summary of Contents for UNO-T

Reviews:

Related manuals for UNO-T

Brands by name

Popular brands

Okolab UNO-T, Manual

Search results

Summary of Contents for UNO-T

Reviews:

Related manuals for UNO-T

Brands by name

Popular brands