Okolab UNO-T Manual Download Page 55

Page: 55 / 73

Figure 78. Homepage - Logging to USB drive.

Note

►

When connecting the USB drive to UNO-CONTROLLER, a USB drive icon

appears on the

Homepage. If you activate the logging on USB drive, a red dot appears on the USB drive, to remind that the
USB drive should not be disconnected while data logging is ongoing see Figure 78.

8.2.7

Alarms

UNO-CONTROLLER allows activating visual and audible alarms.

To set the alarms specifications, press the

Alarms

icon

(see Figure 79 a), then follow the indications

below:

Insert the alarm time; i.e. the time for which the temperature may remain outside the allowed tolerance

before the controller triggers in alarm (see pointer 1 in Figure 79 b).

Note

►

The alarm time range is 5-20 minutes.

Insert the

Tolerance

value. This value defines the allowed tolerance from the set point (see pointer 2 in

Figure 79 b).

Note

►

The tolerance vale range is 0.1-2.0°C.

Insert the transient time; i.e. the maximum time that the system can take to reach a new set point, without

triggering the alarm (see pointer 3 in Figure 79 b).

Note

►

The transient time range is 30

–

240 minutes-.

Press

Save

to confirm (see pointer 3 in Figure 79 b).

Figure 79. How to enter the Alarms menu (a -b).

Summary of Contents for UNO-T










































































Search results

Summary of Contents for UNO-T

Reviews:

Related manuals for UNO-T

Brands by name

Popular brands

Okolab UNO-T, Manual

Search results

Summary of Contents for UNO-T

Reviews:

Related manuals for UNO-T

Brands by name

Popular brands