OKIFAX OF-7 Field Service Handbook Download Page 20

Page: 20 / 142

Item

Specifications

(2) Shape

Documents must be rectangular in shape.

(3) Opacity

The machine will properly reproduce documents

whose opacity is more than 60% is normal mode/and

more than

photo mode.

(4) Automatic Document

Feeder (ADF)

Max. 5 documents/A4 size

Document Damage

The document will not be marked, wrinkled or torn as a
result of being sent throuth the feeder or scanner.

Document Jam Detection

(1) Within

Transmission will

a line disconnectwill

occur when the end of the document is not
detected within lm after scanning begins.

(2) 5 seconds

Notice will be given if the document does not reach

the scanning position within 5 seconds after the
document feed begins.

Document Jam Removal

If document is not

document feed begins

after pressing COPY key.

Summary of Contents for OF-7















































































































































Search results

Summary of Contents for OF-7

Reviews:

Brands by name

Popular brands

OKIFAX OF-7, Field Service Handbook

Search results

Summary of Contents for OF-7

Reviews:

Brands by name

Popular brands