manualshive.com logo in svg

Oki OKIPAGE 4M, Maintenance Manual, Page: 78 / 124

Share
Download
Oki OKIPAGE 4M Maintenance Manual Download Page 78

6 - 7

1

The OKIPAGE 4w Plus/4m malfunctions after the power supply has been
turned on.

• Turn the power supply off, then on again.

• Is the LED lamp on?

• No

Is the AC cable connected correctly?

• No

Connect the AC cable correctly.

• Yes Is  +5 V supplied between CN1 Pin 7 and CN1 Pin 13 of the high-voltage

power supply board?

(Pin 7:  +5 V, Pin 13:  0 V)

• No

Are the CN1 connectors of the high-voltage power supply board and

main control board connected correctly?

• No

Connect the CN1 connectors correctly.

• Yes

Is +5 V supplied between CN2 Pin 2 and CN2 Pin 3 of the main

control board?

(Pin 2:  +5 V, Pin 3:  0 V)

• No

Replace the power supply board.

• Yes

Replace the main control board.

• Yes Is 1-2 V voltage supplied between CN1 Pin 2 and CN1 Pin 13 of the high-

voltage power supply board?

• No

Replace the main control board.

• Yes Replace the high-voltage power supply board.

• Yes

Replace the main control board.

Summary of Contents for OKIPAGE 4M





























































































































Reviews:

No comments