manualshive.com logo in svg

Oki IP-5530, User Manual, Page: 106 / 265

Share
Download
Oki IP-5530 User Manual Download Page 106

106

Maintenance

E Wiper blade cleanliness check and replacement 

Wiper blades check

Check that the wiper blades are not damaged or dirty during the daily inspection.
If one of the wiper blades is as shown below, replace it following the F Wiper blade cleanliness check and 
replacement procedure on 

 

page 106

.

 

 

1

 

PRINTER READY 
01: PAPER / 1626mm

 

              

  

Press the 

MAINTENANCE

 button.

2

 

MAINTENANCE  

   

2

START MAINTENANCE 

 

              

  

Press the 

Down

 button to select 

WIPER 

MAINTENANCE

.

3

 

MAINTENANCE  

   

2

WIPER MAINTENANCE 

 

              

  

Press the 

OK

 button.

4

 

>WIPER MAINTENANCE  

   

2

WIPER BLADE CHECK 

 

              

  

, 

, 

Press the 

Up

 and 

Down

 buttons to select 

WIPER BLADE CHECK

, and then press the 

OK

 

button.

5

 

>>WIPER BLADE CHECK 
 OK? 

 

              

  

Press the 

OK

 button to start the operation. 

To cancel the operation, press the 

CANCEL

 button.

6

 

WIPER IS MOVING...
PLEASE WAIT

 

              

  The part stops moving.

Summary of Contents for IP-5530










































































































































































































































































Reviews:

No comments