background image

Okayo Portable PA System

8

1. Ensure microphone is switched off before inserting batteries.

2. Remove battery clip. Insert 2 x AA batteries (alkaline or rechargeable’s are recommended). 

3. Switch the top mounted power switch to ON. The power LED will illuminate red and “ON” will be displayed on the
LCD screen. 

4. A selection switch on the side of the beltpack provides three level settings (low, mid & high) depending on the appli-
cation or environment in which the portable PA is to be used. The mute button allows beltpack to be put on standby
without switching the power off. 

5. The LCD screen will display the channel selected. To determine which frequency this channel is operating on, press
the UP or DOWN frequency adjustment buttons. 

6. Press the frequency set button for 1-2 seconds. The LCD screen will flash the currently selected channel number.
You can cycle through the channels by pressing the UP or DOWN frequency adjustment buttons. Press the frequency
set button again to lock in your channel selection.

7. The battery status is displayed on the left of the screen. When battery capacity is critical the icon will flash 3 times
before switching the microphone off automatically. 

8. When using with rechargeable NiMH batteries, you can us the C 7196 charging pod. This allows you to put up to 2
beltpacks on charge at the same time. Charging time is dependant on the capacity of batteries used, typically 10-12
hours charging is required. If battery icon is flashing when charger is connected, ensure rechargeable batteries are
inserted in the microphone. If batteries have failed both the battery icon and screen backlight will flash. 

During normal charging the battery icon will cycle through the charge “block” icons. Once full capacity is reached the
full battery icon and all “blocks” will be displayed. 

Troubleshooting

• Power LED does not illuminate after switching on

Check batteries are charged and inserted correctly. 

• LCD shows “Err” when switching off

Contact your place of purchase for information on resetting your beltpack. 

• LCD panel displays garbled information

Remove batteries and re-insert them

• No sound output

Check frequency of transmitter is the same as the portable PA receiver
Check volume level of both transmitter and portable PA receiver
Check mute button is not activated
Ensure beltpack is within range of the receiver
Check for sources of interference, large metal objects etc within range of the beltpack

• Signal disturbance

When operating two transmitters in the same area, ensure frequencies selected are several channels apart. This
helps to reduce crosstalk between transmitters.  Also note that other wireless devices can cause interference.
Ensure you adjust your frequency around these devices where possible.

Summary of Contents for C 7192











Reviews: