5
6
●
If the product is found unstable due to loose
bolts or screws, retighten them as soon as
possible.
●
This instruction manual is very important, so
store it in an easily accessible location.
●
Regular maintenance is recommended for
long product life.
Make requests to us immediately when a
repair or inspection is needed (fees required
after expiration of warranty).
●
If liquid is spilled on the product, wipe it off
immediately.
· The surface may discolor, deteriorate, or
get damaged by using alcohol, thinner,
benzene, etc.
●
Some products may have a noticeable
wood smell. Ventilation on a regular basis is
recommended.
●
Tighten loose bolts and screws on a regular
basis.
Operation Guide
■
Leg adjustment
Use the leveler for the legs to keep the bench
horizontal to the floor surface if it wobbles
due to uneven floor surfaces.
When using the leveler, ensure that more
than two people provide rigid support
using extreme caution.
Caution
Leveler
Lower
Higher
20mm
Legs
■
Bench layout
When placing more than one product adjacent to each other, they should be connected or use the
dedicated spacer.
If you want to connect a tiered bench to another in S-shaped arrangement as shown below, be
sure to use the dedicated spacer.
·
Spacer MB815Z-Z25 (black), ZA75 (white)
For details, consult our official dealer.
Spacer
Spacer
Spacer
Spacer
■
Seat cushion (optional)
●
Felt seat cushions with an anti-slip bottom are available.
●
Do not use the seat cushions in an unsettled position.
●
Do not bend the seat cushion. Folding damages the material.
For details, consult our official dealer.
■
Magnetic vertical wiring duct (optional)
Attach the magnetic vertical wiring duct to the inner-facing side of a leg.
The wiring duct can be attached to the end leg or the middle leg.
Tiered Bench
Magnetic vertical
wiring duct
Please follow instructions below. Failure to do so may cause serious damage to the product
and Okamura will have no responsibility for any damages.
Operating Precautions and Maintenance
Instructions to Extend the Life of Product
For daily care
Wooden part
●
Wipe gently along the grain with a soft, clean,
dry cloth.
●
If the product becomes noticeably dirty,
remove the dirt using a soft cloth dampened
with water, then use a dry cloth to absorb
water residue.
●
For a more thorough cleaning we recommend
using a mild cleaner (thin neutral detergent).
〈
Caution
〉
●
Do not use the following as they may damage
the coating.
◎
Thinner, benzene, alcohol , lacquer,
oil, vinegar, boiling water, polisher, etc.
●
Frequent wiping with a damp cloth may cause
cracking of the coating. It is recommended
to use a dry soft cloth or our wiping cloths for
daily care.
Resin part
●
Wipe off with a soft cloth dampened with
water.
●
When it gets dirty, moisten the cloth with thin
neutral detergent and squeeze it hard to
wipe.
Wipe clean with a damp cloth. Be sure to
wipe detergent completely and wipe again
with a dry cloth to dry it.
Steel part
●
Wipe off with a dry soft clean cloth.
●
If moisture is collected or substances such
as fingerprints or sebum are adhered,
wipe it off immediately. Leaving moisture,
liquid, fingerprints, or sebum on the surface
accelerates oxidation of the steel part and
deteriorates gloss and texture.
Cloth part/Mesh part
●
Brush with a soft brush or tap the surface
softly and vacuum to remove dust to avoid
damaging the cloth.
●
When it gets dirty after extended period
of time, wipe with a well wrung soft cloth
moistened with thin neutral detergent. Wipe
clean with a damp cloth. Be sure to wipe
detergent completely and wipe again with a
dry cloth to dry it.
●
When using alkaline electrolyzed water to
remove stains, spray directly on the stain
and brush with a soft brush taking care not
to damage the cloth. Then, wipe the moisture
and stain to remove and wait for the cloth to
dry.
●
When it gets an oily stain, dab and remove
it by using a dedicated stain remover
immediately. Then wipe with a soft cloth
dampened with water, followed by a dry cloth
to dry. Stains may be permanent depending
on the material.
