Ojmar Nexo NLX1, Assembly Instructions

Page: 2 / 4

min. 240 mm.
(9.449)
Al pivote de la puerta Al pivote de la puerta
max. 20 mm.
(0.787)
Figura 1.2.-Medidas en mm. (Pulgadas)
Cerradero
Cerradero
Visor de led Visor de led
max. 20 mm.
(0.787)
min. 240 mm.
(9.449)
15
( 0.591)
15
( 0.591)
Cuerpo taquilla Cuerpo taquilla
Puerta taquilla Puerta taquilla
93.5 ±0.1
( 3.681" ±0.004 )
109.5
( 4.311" )
93.5 (3.681"
)
129.5 (5.098"
)
21.6 (0.852"
)
22
( 0.866" )
30
( 1.181" )
30 (1.181"
)
9 (0.354"
)
9 (0.354"
)
93.5 ±0.1
( 3.681" ±0.004 )
109.5
( 4.311" )
93.5
±0.1
(3.681"
±0.004
)
129.5 (5.098"
)
21.6 (0.852"
)
22
( 0.866" )
30
( 1.181" )
30 (1.181"
)
20 (0.787"
)
15 (0.591"
)
15 (0.591"
)
5
( 0,197 )
15 (0.591"
)
15 (0.591"
)
20 (0.787"
)
5
( 0,197" )
15
( 0.591" )
15
( 0.591" )
14,5 (0,571"
)
14,5 (0,571"
)
CERRADURA DERECHA CERRADURA IZQUIERDA
CERRADERO
CERRADERO
Figura 1.2.- Medidas en mm. (Pulgadas)
CERRADURA DERECHA CERRADURA IZQUIERDA
CERRADERO
CERRADERO
93.5±0.1
( 3.681"±0.004)
109.5
( 4.311")
93.5 (3.681"
)
129.5 (5.098"
)
21.6 (0.852"
)
22
( 0.866")
30
( 1.181")
30 (1.181"
)
9 (0.354"
)
9 (0.354"
)
93.5±0.1
( 3.681"±0.004)
109.5
( 4.311")
93.5
±0.1
(3.681"
±0.004
)
129.5 (5.098"
)
21.6 (0.852"
)
22
( 0.866")
30
( 1.181")
30 (1.181"
)
4.5 (0.177"
)
46 (1.811"
)
5
( 0.197")
2.5
( 0.098")
4.5 (0.177"
)
46 (1.811"
)
5
( 0,197")
2.5
( 0.098")
11 (0.433"
)
11 (0.433"
)
Cerradero Cerradero
Cuerpo taquilla Cuerpo taquilla
min. 240 mm.
(9.449)
Al pivote de la puerta
max. 20 mm.
(0.787)
Al pivote de la puerta
Visor de led
max. 20 mm.
(0.787) min. 240 mm.
(9.449)
Visor de led
2.5
( 0.098)
2.5
( 0.098)
The NEXO NLX1 lock is
attached to the locker door with
four screws.
• Recommended screws:
- Conglomerate doors: Pan
head wood screw 4.5 x 35 DIN
7996 stainless steel (depending
on the thickness of the door)
- Phenolic or metal doors: Pan
head screw M5 x 25 DIN 7985
stainless steel (depending on
the thickness of the door)
• The maximum tightening
torque to apply to the tightening
of each screw or coach nut will
be 200 Ncm.
• The diameter of the central
hole should be 23 mm (+1/0
mm). Bevelling the hole on
the inner area of the door is
recommended.
During installation, ensure that
the lock does not collide with
the locker body with the door
open (see design 1.2).
The dimensions and location
of the anchorage points are
shown in the following designs
(the dimensions depend on the
design of the lock and the type
of lock used with the locking
device:
• Striking plate with
reinforcement
Design 1.2 - Measurements
given in mm (inches)
• Flat Striking plate (with
channel on the locker body)
Design 1.3 - Measurements
given in mm (inches)
1.2 ASSEMBLY
INSTRUCTIONS
1.2 Design
Measurements given in mm (inches)
1.3 Design
Measurements given in mm (inches)