OHAUS DEFENDER SERIES Assembly Instructions Manual Download Page 7

Page: 7 / 55

EN-4

3000 Series Indicators

1. INTRODUCTION

This manual contains installation, operation and maintenance instructions for the T31P and T31XW Indicators. Please read this
manual completely before installation and operation.

1.1 Safety Precautions

• Verify that the input voltage range printed on the data label matches the local AC power to be used.

• Make sure that the power cord does not pose a potential obstacle or tripping hazard.

• Use only approved accessories and peripherals.

• Operate the equipment only under ambient conditions specified in these instructions.

• Disconnect the equipment from the power supply before cleaning.

• Do not operate the equipment in hazardous or unstable environments.

• Do not immerse the equipment in water or other liquids.

• Service should only be performed by authorized personnel.

• The T31XW is supplied with a grounded power cable. Use only with a compatible grounded power outlet

For safe and dependable operation of this equipment, please comply with the following safety precautions:

Summary of Contents for DEFENDER SERIES























































Search results

Summary of Contents for DEFENDER SERIES

Reviews:

Brands by name

Popular brands

OHAUS DEFENDER SERIES, Assembly Instructions Manual

Search results

Summary of Contents for DEFENDER SERIES

Reviews:

Brands by name

Popular brands