background image

SHIFT UP TIMING ADJUSTMENT 

* Adjust the engine before adjusting the clutch shift timing.
  Adjust the engine as per engine instruction manual.

1. Once the engine adjustments  have been completed, proceed to the 
    adjustment of the clutch shoe shift timing.
    (Using a 1.5mm allen wrench to adjust  the clutch shoe on either side.)
    
    Note:
              Clockwise--------Shift timing will become slower.
              Counter-clockwise---Shift timing will become quicker.
 
2. Adjust the clutch shift timing for your track conditions.
     As you tighten (Clockwise) the 2x10mm screw , the shift timing will 
     become slower.
     As you loosen (Counter-clockwise ) the 2x10mm screw, the shift timing 
     will become quicker.

3. Set the shift  timing to the track conditions while the car is running.

M2x10mm 
Hex Screw

M2x10 
Hex Screw

3x3mm
Set Screw

* Use a 1.5mm allen wrench to 
  set the clutch shoe.

* Adjust the 3x3 set screw witch is used
   to 

the distance between the clutch

   shoe and clutch bell. 

adjust 

* Adjust the M2 x 10mm hex screw will be
   change the shift timing of the clutch
   shoe. 

ADJUSTING THE SHIFT POINT

1.5mm
 Allen  Wrench

Clockwise
 (Tighten)

Counter-clockwise
    (Loosen)

INSTRUCTIONS 

#38322 STANDARD SPEED TRANSMISSION

2 SPEED GEAR RATIO COMBINATIONS

2 SPEED OPTION PARTS

IMPORTANT:
The sum of the spur gear and clutch gear for1st gear must be equal.
Also, he sum of the spur gear and clutch gear for 2nd  gear 

.  

be equal

Example:

1st gear 45+13=58
2nd gear 41+17=58

Must be equal

* Also 2 tooth and 5 tooth differences are possible, but not shown.. 

SPUR GEAR

CLUTCH GEAR 

16T/20T

44T/40T

43T/39T

42T/38T

41T/37T

(4 tooth  difference - OFNA  standard)

17T/21T

18T/22T

19T/23T

S

h

o

rt

 T

ra

c

k

T

o

rq

u

e

T

o

p

 S

p

e

e

d

L

o

n

g

 T

ra

c

k

SPUR GEAR

CLUTCH GEAR 

16T/21T

44T/39T

43T/38T

42T/37T

(5 tooth  difference)

17T/22T

18T/23T

19T/24T

S

h

o

rt

 T

ra

c

k

T

o

rq

u

e

T

o

p

 S

p

e

e

d

L

o

n

g

 T

ra

c

k

( STANDARD)

¤j¾¦

(MODIFY)

38298              37T Spur Gear, Gray 1st 

38299              41T Spur Gear, Gray 2nd

38300              38T Spur Gear, Gray 1st

38301              42T Spur Gear, Gray 2nd

38302              39T Spur Gear, Gray 1st

38303              43T Spur Gear, Gray 2nd

38304              40T Spur Gear, Gray 1st

38305              44T Spur Gear, Gray 2nd

SPUR GEAR:

Number

Description

CLUTCH GEAR:

Number

35944              16T-1st Clutch Gear

38306              17T-1st Clutch Gear

38307              18T-1st Clutch Gear

38308              19T-1st Clutch Gear

35945              20T-2nd Clutch Gear

35946              21T-2nd Clutch Gear

38309              22T-2nd Clutch Gear

38310              23T-2nd Clutch Gear

38311               24t-2nd Clutch Gear               

Description

Here

NOT Here, at ball set screw!

STANDARD GEARING

Summary of Contents for CD-3 SPORT RTR






























Reviews: