OfiTE 170-95 Instruction Manual Download Page 23

OFITE, 11302 Steeplecrest Dr., Houston, TX 77065 USA / Tel: 832-320-7300 / Fax: 713-880-9886 / www.ofite.com

22

Warranty and 

Return Policy

Warranty:

OFI Testing Equipment, Inc. (OFITE) warrants that the products shall be free from liens and defects in 

title, and shall conform in all respects to the terms of the sales order and the specifications applicable 

to the products. All products shall be furnished subject to OFITE’s standard manufacturing variations 

and practices. Unless the warranty period is otherwise extended in writing, the following warranty shall 

apply: if, at any time prior to twelve (12) months from the date of invoice, the products, or any part 

thereof, do not conform to these warranties or to the specifications applicable thereto, and OFITE is 

so notified in writing upon discovery, OFITE shall promptly repair or replace the defective products. 

Notwithstanding the foregoing, OFITE’s warranty obligations shall not extend to any use by the buyer 

of the products in conditions more severe than OFITE’s recommendations, nor to any defects which 

were visually observable by the buyer but which are not promptly brought to OFITE’s attention.

In the event that the buyer has purchased installation and commissioning services on 

applicable products, the above warranty shall extend for an additional period of twelve 

(12) months from the date of the original warranty expiration for such products.

In the event that OFITE is requested to provide customized research and development for the buyer, 

OFITE shall use its best efforts but makes no guarantees to the buyer that any products will be provided.

OFITE makes no other warranties or guarantees to the buyer, either express or implied, 

and the warranties provided in this clause shall be exclusive of any other warranties 

including ANY IMPLIED OR STATUTORY WARRANTIES OF FITNESS FOR PURPOSE, 

MERCHANTABILITY, AND OTHER STATUTORY REMEDIES WHICH ARE WAIVED.

This limited warranty does not cover any losses or damages that occur as a result of:

• 

Improper installation or maintenance of the products

• 

Misuse

• 

Neglect

• 

Adjustment by non-authorized sources

• 

Improper environment

• 

Excessive or inadequate heating or air conditioning or electrical 

power failures, surges, or other irregularities

• 

Equipment, products, or material not manufactured by OFITE

• 

Firmware or hardware that have been modified or altered by a third party

• 

Consumable parts (bearings, accessories, etc.)

Returns and Repairs:

Items being returned must be carefully packaged to prevent damage in 

shipment and insured against possible damage or loss. OFITE will not be 

responsible for equipment damaged due to insufficient packaging.

Any non-defective items returned to OFITE within ninety (90) days of invoice are subject to a 

15% restocking fee. Items returned must be received by OFITE in original condition for it to 

be accepted. Reagents and special order items will not be accepted for return or refund.

OFITE employs experienced personnel to service and repair equipment manufactured by us, as 

well as other companies. To help expedite the repair process, please include a repair form with all 

equipment sent to OFITE for repair. Be sure to include your name, company name, phone number, 

email address, detailed description of work to be done, purchase order number, and a shipping address 

for returning the equipment. All repairs performed as “repair as needed” are subject to the ninety (90) 

day limited warranty. All “Certified Repairs” are subject to the twelve (12) month limited warranty.

Returns and potential warranty repairs require a Return Material Authorization (RMA) 

number. An RMA form is available from your sales or service representative.

Please ship all equipment (with the RMA number for returns or warranty repairs) to the following address:

OFI Testing Equipment, Inc. 

 

Attn: Repair Department 

 

11302 Steeplecrest Dr. 

 

Houston, TX 77065

 

USA 

OFITE also offers competitive service contracts for repairing and/or maintaining your lab 

equipment, including equipment from other manufacturers. For more information about 

our technical support and repair services, please contact [email protected].

Summary of Contents for 170-95
























Reviews: