OfiTE 120-60 Instruction Manual Download Page 9

OFITE, 11302 Steeplecrest Dr., Houston, TX 77065 USA / Tel: 832-320-7300 / Fax: 713-880-9886 / www.ofite.com

8

Operation

The blending assembly has two speeds, “HI” and “LO”. The Constant Speed 

Blender will not operate unless the blending assembly is set to “HI”. Before 

operation, press the “HI” button on the blending assembly.

The unit has three operating modes: Manual, Variable, and Auto. The 

MAN/

AUTO - Variable

 switch (13) and the 

MAN/AUTO

 switch (15) set the mode.

1.  To set the unit to Manual Mode, set the 

MAN/AUTO - Variable

 switch (13) 

to 

MAN/AUTO

 and the 

MAN - AUTO

 switch (15) to 

MAN

.

2.  To set the unit to Auto Mode, set the 

MAN/AUTO - Variable

 switch (13) to 

MAN/AUTO

 and the 

MAN - AUTO

 switch (15) to 

AUTO

.

3.  To set the unit to Variable Mode, set the 

MAN/AUTO - Variable

 switch 

(13) to 

Variable

.

Before turning the unit on, be sure to set the MAN/AUTO switch (15) 

and the ST PT 1 / ST PT 2 switch (14) to the center position and turn 

the Potentiometer (16) fully counter-clockwise.

1.  Place the mix water into the mixing cup and place the lid on top of the 

container.

2.  The 

MAN/AUTO - Variable

 switch (13) should be in the 

MAN/AUTO

 

position. The 

MAN/AUTO

 switch (15) should be in the 

MAN

 position.

3.  Place the 

ST PT 1 / ST PT 2

 switch (14) to the 

ST PT 1

 position to start 

the unit.

When you initially start the unit, the rotational speed may exceed the 

setpoint, but will stabilize within a few seconds.

4.  After stabilization, you have 15 seconds to add the cement to the mix 

water and cover the container with the lid. Reset the timer to zero by 

pressing the Reset Button (8).

5.  After 15 seconds, increase the rotational speed by setting the 

ST PT 1 / 

ST PT 2

 switch (14) to 

ST PT 2

.

6.  After mixing the cement an additional 35 seconds, stop the blender by 

setting the 

ST PT 1 / ST PT 2

 switch (14) to the center position.

7.  Return the 

MAN/AUTO

 switch (15) to the center position.

8.  After mixing is complete, clean the blending cup and lid as soon as 

possible to prevent any cement from building up on the container.

Operation 

Manual Mode

Summary of Contents for 120-60














Reviews: