Officine Gullo
6
DECLARATION OF COMPLIANCE
This appliance is manufactured by OFFICINE GULLO S.r.l
Headquarters and factory
Via Della Torricella 29, Antella, Bagno a Ripoli
50012 Florence - Italy
Tel. +39 055 65 60 3324
+39 055 62 18 07
officinegullo.com | [email protected]
The manufacturer declares that the appliances are compliant with the prescriptions of the 2004/108/CE norm for
the electric part. The installation must be done observing the norms in force.
N.B.: The manufacturer declines any responsibility for direct or indirect damage caused by improper or incorrect
installation, alterations, maintenance or use of the appliance, as in all the other cases considered in the items of our
sales conditions.
ELECTRIC TECHNICAL DATA TABLE
MODEL
Dimensions
cm
Power Supply
Tot.
power
(KW)
Max.
absorb
A
Power
supply
cable mm²
FES 10
100x63x57h
400V~3N 50/60 Hz
5
10,4
5x1,5
INSTALLATION
The installation, start-up and maintenance of this appliance must be carried out only by qualified fitters. All installation
operations must be in accordance with current regulations. The manufacturer declines all responsibility for
malfunctioning due to bad or faulty installation.
Attention:
In accordance with international rules, when connecting the appliance, an automatic device enabling the
disconnection of all contacts from the mains, must be installed above it; this device must have a contacts opening
of at least 3 mm.
ELECTRIC CONNECTION
The terminal board is situated behind the front panel. The electrical wiring must be no less than HO5 RN F and have
a section suitable for the appliance. Secure the wiring with the wiring clips. Connect the wire ends to their terminals
on the terminal board. The earthing wire must be longer than the other wires so that it will disconnect after the live
wires in the event of the fastener breaking.
EQUIPOTENTIAL
The appliance must be connected to an equipotential system.
The connection screw is positioned at the back of the appliance and is identified by the symbol
.
Attention!
The manufacturer will neither be held responsible for, nor will give any compensation during the guarantee
period for any damage caused, and which is due to inadequate installations not compliant with the instructions.
7
Officine Gullo
USER MANUAL
INSTRUCTIONS FOR USE
Attention! The appliance must only be used under surveillance.
LIGHTING AND REGULATING THE ELECTRIC OVEN
Before turning the oven on, make sure the oven racks are in the desired position.
Turn the control knob to the right and set the temperature wanted.
To turn the oven off, turn the knob to the left to position 0.
To turn the oven on, turn the selector knob (see figure) to the right or left into one of the
following positions
Top + bottom heating element
Bottom heating element
Top heating element
Preheating the oven is essential for baking. It is recommended to pre-heat the oven
slightly warmer than the cooking set point fot at least 30 minutes. All cooking times are
based on a preheated oven unless otherwise stated in the recipe.
Caution:
when the oven is on the door must be kept shut otherwise the knobs and
protection sheet could get hot and be damaged.
CLEANING AND MAINTENANCE
Attention! During cleaning, do not wash the external parts of the appliance with direct sprays of water or with high
pressure.
After every use, clean the appliance thoroughly. Daily cleaning after switching off the appliance ensures the perfect
functioning and long life of the appliance.
Before starting to clean the appliance, disconnect the power supply. The parts in steel must be washed with hot water
and neutral detergent, then rinsed thoroughly in order to eliminate all traces of detergent; after which, dried with a
dry cloth. Do not use abrasive or corrosive detergents.
The enamelled parts should be washed with soapy water.
Oven: Cleaning the oven is made easier by removing the support grill.
Important: As well as ordinary cleaning and maintenance, it is advisable to have the installation checked by an
installer at least once a year.
It is therefore suggested to draw up an after-sales assistance contract.
